Rear Panel - Fender RUMBLE 15 Mode D'emploi

Thanks for buying a Fender® Rumble™ series bass amplifier. Fender
bass amplification provides thick, natural and balanced tone that
sits fat in your live or studio mix. Rumble amps are designed by
bass players. Full-featured and easy to operate, the Rumble family
gives you high-quality bass tone and incredible value.
E Q U A L I Z A T I O N
5 0 0
2 8
0 10 -15 +15 -15 +15
INPUT V OLUME BASS MID
O V E R D R I V E
5 5
1 2
2 8 2
0 10 0
INPUTS V OLUME GAIN
A. INPUT 1 — Plug your passive or active bass in here. If
your bass is too hot and causes distortion, try using
INPUT 2.
B. INPUT 2 — A lower sensitivity input (-6dB) providing
more headroom to reduce distortion from high output
basses.
NOTE: Both INPUT 1 and 2 can be used simultaneously for
two instruments. In this situation, each input will have a
lower input sensitivity (-6dB).
C. VOLUME — Controls the loudness of the amplifier.
D. GAIN — Controls the amount of OVERDRIVE distortion.
F. BLEND — Controls the amount of distortion (set by
GAIN) to be blended with the clean bass signal. Lower
settings can maintain a cleaner tone, with some added
grit. Higher settings will produce more distorted tones
and add sustain.
E. ENABLE — Press this button to turn the OVERDRIVE
on or off. The red LED (light) illuminates when the
OVERDRIVE is on.
G. SHAPE FILTERS:
• PUNCH — Emphasizes tight punchy bass response,
useful for finger style playing or for enhancing the tonal
character of a bridge pickup.
• SCOOP — Mid-frequency cut, combined with low-and-
high-frequency boosts that offer a fat pleasing tone,
useful for slap style playing, low-volume practice, or in
combination with OVERDRIVE.
6 6
All manuals and user guides at all-guides.com
Rumble® 15 / 30 / 75 Bass Amps Rumble® 15 / 30 / 75 Bass Amps
0
-15 +15
HEAD 15W BASS
TREBLE AUX IN PHONES AMPLIFIER POWER
S H A P E
50% 0
8
10 CLEAN DRIVE -15 +15
ENABLE PUNCH SCOOP
BLEND BASS
fender.com fender.com
The Fender Precision Bass® Guitar was introduced in 1951, forever
changing music and giving birth to a new kind of musician—the
electric bassist. Since then music has never been the same. Your
new Rumble will provide years of enjoyment as you continue your
musical journey and make history!
O V E R D R I V E
5 5
1 2
2 8 2
0 10 0 10
INPUTS V OLUME GAIN
E Q U A L I Z A T I O N
0 0 0
-15 +15 -15 +15 -15 +15
LOW MID HIGH MID TREBLE AUX IN
H. EQUALIZATION — Used to adjust overall tone and to
compensate for room acoustics. Remember, what sounds
harsh in one room may have just the right edge in
another room.
I. AUX IN — Plug your CD player or mp3 player in here.
The amp controls do not affect this input. Adjust the
volume or tone of the aux signal at its source.
J. HEADPHONES — Plug your stereo headphones (32
ohms minimum impedance) in here. Speaker output is
automatically disabled.
K. LINE OUT — Balanced output to connect to external
devices such as PA systems and recording consoles. Use
a balanced stereo cable (TRS→XLR or TRS→TRS) to reduce
noise and hum. Mono (unbalanced) cables can also be
used, but may be noisier. The level and tone of the LINE
OUT signal is affected by all pre-amp controls, including
Volume.
L. FOOTSWITCH — Allows for remote switching of
OVERDRIVE. See the following page for details.
M. POWER — Switches the amplifier ON/OFF as indicated
by the power light.
N. IEC POWER CORD SOCKET — Connect the included
power cord to a grounded A/C electrical
outlet in accordance with the voltage and
frequency ratings specified on the rear
panel of your amplifier.
E Q U A L I Z A T I O N
50% 0 0 0
8
CLEAN DRIVE -15 +15 -15 +15 -15 +15
ENABLE
BLEND BASS MID TREBLE AUX IN
75W BASS
HEAD LINE FOOT
PHONES OUT SWITCH AMPLIFIER

Rear Panel

Rear Panel
HEAD 30W BASS
PHONES AMPLIFIER POWER
POWER