Contents
Contents
1
Key to symbols and safety instructions . . . . . . . . . . . . . . . . . 10
1.1
Key to symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2
Product details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1
Standard delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.2
Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.3
3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2
3.3
4
Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5
6
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1
Key to symbols and safety instructions
1.1
Key to symbols
Warnings
Warnings in this document are identified by a warning
triangle printed against a grey background.
Keywords at the start of a warning indicate the type and
seriousness of the ensuing risk if measures to prevent
the risk are not taken.
The following keywords are defined and can be used in this document:
• NOTE indicates a situation that could result in damage to property or
equipment.
• CAUTION indicates a situation that could result in minor to medium
injury.
• WARNING indicates a situation that could result in severe injury or
death.
• DANGER indicates a situation that will result in severe injury or death.
Important information
This symbol indicates important information where
there is no risk to people or property.
Additional symbols
Symbol
Explanation
▶
Step in an action sequence
Cross-reference to another part of the document
•
List entry
-
List entry (second level)
Table 7
10
1.2
Safety instructions
▶ Observe all country-specific regulations and standards during
installation and operation.
▶ Observe all instructions to ensure satisfactory operation.
▶ This product must only be installed and commissioned by an
approved contractor.
▶ Never install this product in wet rooms.
▶ Install and commission heat sources and other accessories according
to the relevant instructions.
▶ Use this product exclusively in conjunction with the programming
units and heat sources listed. Observe connection diagram.
▶ Use the power supply unit provided to connect this product to the
230 V mains supply.
About these instructions
These installation instructions contain important information regarding
the safe and proper installation, commissioning and maintenance of the
product.
These installation instructions are intended for qualified contractors
who, as a result of their training and experience, are skilled in dealing
with electrical installations and heating systems.
2
Product details
To fully use all functions, internet access is required. This
may incur additional costs.
Also, the JunkersHome app, which is subject to charge,
is required to control the system via a smartphone.
• Interface between heating system and a network (LAN)
• Controlling and monitoring a system using a smartphone
The MB LAN cannot be combined with a room
temperature-dependent FR 50.
• May be combined with the following:
- Heat sources with 2-wire BUS interface and controllers FW.../FR...
from FD 889 (09/2008) with 2-wire BUS interface, e.g. FW 200
- Modules for controllers FW.../FR... from FD 889 (09/2008), e.g.
ISM2.
- Heat pumps with REGO1000 basic controller from V1.10.
2.1
Standard delivery
Fig. 1, page 62:
[1]
Module
[2]
Plug power supply unit with connecting cable
[3]
CAT 5 LAN cable
[4]
Bag with installation material
[5]
Installation instructions
1) Connecting this module requires a router with available RJ45 socket.
2) To see which devices are supported, please go to our home page.
1)
.
2)
MB LAN - 6 720 805 489 (2013/01)