Care And Maintenance - Baby Jogger City Mini 2 Mode D'emploi

UNPACK
EN
1 After unboxing the pram, raise the canopy until
it clicks into place, then undo the four fastening
strips around the canopy.
2 Then remove the mattress, and undo the
six fastening strips around the pram body to
remove the liner.
3 Next, pull on the handles inside the pram body
to move the support bars into position. Make
sure the support bars insert into the retaining
clips until they click into place.
Finally, reattach the liner and canopy, then
place the mattress back inside the pram.
MOUNTING ADAPTERS
4 Make sure the elastic fabric near the accessory
mounting slots is not covering the slots.
5 Insert Adapter Brackets into the corresponding
mounting brackets on your stroller/pushchair.
The Adapter Brackets are secure when they
click into place.
NOTE: Left and right are determined by
standing in front of and facing the stroller/
pushchair and each Adapter Bracket is labeled
with an L or an R for your convenience.
WARNING: Keep child's hands clear when
installing the adapter brackets.
6 Push the gray release button on each adapter
and pull upward to remove.
NOTE: Remove the adapter brackets before
folding the stroller.
FOOT COVER
7 To attach the foot cover, place the foot cover
over the Pram frame.
8 Attach the fastening strips on either side of the
pram body.
9 On each side of the foot cover, thread the snap
through the loop and close the snaps together
to secure the foot cover to the pram frame.
10 You may also fold the top of the foot cover
down and secure it using the lower loops.
CANOPY
11 Raise the canopy until it clicks into position
B. Continue to raise the canopy to position A
by pressing the buttons on either side of the
canopy hinge.
WARNING: Before carrying or lifting, make sure
that the canopy is locked into position A.
NOTE: The canopy has 2 locked positions.
Push and pull the handle to make sure the
canopy is in a locked position. The canopy can
be in any position when used in the stroller.
12 To lower the canopy, press the buttons on
either side of the canopy hinge then lower the
canopy.
13 To use the canopy window, unzip the canopy
zipper. Then roll the shade up towards the top.
ATTACH TO STROLLER
14 First, recline the backrest by pinching the
clamp behind the backrest, and slide it down
to the lowest position.
15 Pull backrest down on both sides to match the
clamp position.
NOTE: The stroller canopy MUST be removed
before attaching the pram.
WARNING: When making adjustments to the
stroller seat, make sure child' s head, arms, and
legs are clear of moving seat parts and stroller
frame.
16 Align the black attachment brackets of
the Pram body with the mounting adapter
brackets. The Pram body can only be attached
rear facing. Firmly press down on the pram
body until you hear it click into place. Gently
pull up on the canopy handle to ensure it is
locked in place.
17 To remove the pram body from the stroller:
Lift the release levers on each side of the pram
body and pull upward to remove.
REMOVING THE INNER FABRIC
18 Unzip the canopy from the handle.
19 Undo the four fastening strips around the
canopy. then remove the canopy fabric.
20 Undo the six fastening strips around the pram
body to remove the liner.

CARE AND MAINTENANCE

Mattress Cover & Foot Cover:
• Remove plastic & foam inserts from the
mattress before washing.
• Machine wash separately using a warm
gentle cycle and mild detergent.
• Do not bleach.
• Do not iron.
• Do not place fabric in the dryer. Lay flat to dry.
Pram Base, Canopy & Mattress Pad:
• Wipe clean using a damp cloth.
• Do not bleach.
• Do not iron.
7
EN