Publicité
Astronomical/annual time switch
AstroRex DY64
A4 11 63, A4 11 64
Safety notes
This product may be installed only by a qualified electrician. Non-compliance may result in a fire hazard or electric shocks. Before
installation, read the operating instructions and observe the product-specific requirements for the installation location. Use only original spare parts for
repair and maintenance. All products may be opened and repaired only by specially trained personnel. Unauthorised opening and repair by other per-
sons will invalidate all claims for liability, replacement or warranty services. When operated from the mains voltage, the time switch may not be used to
switch safe extra-low voltages (SELV). When operated from a safe extra-low voltage, it may not be used to switch mains voltages.
One-week overview of the
programmed switching times.
Resolution: 0.5 h
Channel number
Switch state
Function
Day, time, date
Menu selection, back in menu,
Actuation >1s = operating display
Confirm a selection or
accept a parameter setting
• Selection of a menu item or set a parameter.
• Channel selection
R
3600W
1800W
Overview
Technical data
A4 11 63
A4 11 64
Supply voltage:
120 / 230V 50/60Hz
24 AC/DC
Power consumption:
approx. 0,3...2 W
approx. 3...4 W
4 changeover contacts 16A 250V~ cos ϕ = 1
Relay outputs 1- 4:
Accuracy:
± 0,2 s/day under typical installation conditions
single-strand
multi-strand
2
Wire cross-sections:
1,5...4 mm
1,5...2,5 mm
Programs
4 channels x 3 program types x 28 programs
Control signal for channel 1:
supply voltage, referred to neutral
Control-pulse duration:
> 200ms
Control-wire length:
max. 50m
Lithium battery module
Ref. A4 01 26
1
A4 11 63
2
1
4
2
4
M
120V/230V 50/60Hz
˜
R6a -20T
1
2
ON
ON
AUTO
AUTO
OFF
OFF
Socket for
+
3
4
data key
ON
ON
AUTO
AUTO
Ref. A4 01 25
OFF
OFF
120V/230V~50/60Hz
Separate
L
N S >1
2
1
4
1
4
manual switch
M
2
4
3
˜
for each
channel
+
+
+
100W
1800W
1800W
2300W
1400VA
Delay time:
0 ... 23 h 59 min 59 s
Local coordinates:
Resolution 1°
Battery reserve:
5 years
Storage temperature:
- 20°C to +60°C
Operating principle:
Typ 1.B. S. T. IEC/EN 60730-2-7
2
Operation in a normal environment
Degree of contamination:
2
Installation:
in distribution panel
General information
• Starting: After connection of the supply voltage, the clock
starts to run with the last selected function. The relay
position is determined by the currently active program.
• Backup battery operation mode:
- background lighting not available.
- data key READ/WRITE only via the menu.
• If, during programming, no key is pressed for 60 seconds,
the timer automatically switches from the menu display to
the normal operating display.
• The channel switch states will be updated when
programming has been completed.
C
Astro
Select country.
Select the city
closest to the
c
planned location
for use.
1x 58W 7F
You can adjust the coordinates
more precisely with
LONGITUDE and
LATITUDE.
Use the enclosed time-zone map to set
the correct time zone.
From this map, determine the difference
between local time and UTC (Universal Time
Coordinated) and set this value.
D
Offset
The time switch switches on at the calculated sunset time and off at the calculated sunrise time.
By setting an offset, you can shift the switching times by up to ±120 minutes with respect to the calculated sunrise and sunset times.
Example: If you set the offset to +30 minutes, the time switch will switch 30 minutes after sunrise and 30 minutes after sunset.
If you set the offset to -30 minutes, the time switch will switch 30 minutes before sunrise and 30 minutes before sunset.
Select language
B
Summer time +1h
Europe: factory setting.
Special: The dates for switching to and from
summer time can be set as desired by entering
a start date and end date. In the following
years, switching will be carried out on the
corresponding day of the week (e.g. Sunday).
Factory setting: 8°E 52°N
The MINUS key is used to adjust the westward longitude value in the range from
000°EAST/WEST to 180°WEST.
The PLUS key is used to adjust the eastward longitude value in the range from
000°EAST/WEST to 180°EAST.
The PLUS key is used to adjust the northward latitude value in the range from
00°NORTH/SOUTH to 90°NORTH.
The MINUS key is used to adjust the southward latitude value in the range from
00°NORTH/SOUTH to 90°SOUTH.
t
0h
3
6
9
12
1
+
0
max. 120min
Setting
A
Time and date
15
18
21
24h
+
max. 120min
Publicité
