Edge Band Trimming - Festool OF 1010 Q Notice D'utilisation D'origine

6.8

Edge band trimming

Protruding edge bands can be fl ush trimmed with
the angle arm WA-OF (7.6) in connection with the
guide plate UP-OF (7.3).
- Screw the angle arm into the platen's threaded
bore (7.7) with the rotating knob (7.5).
- Bolt the guide plate to the angle arm with the
rotating knob (7.4).
- Adjust the milling depth so that this is equal to
the thickness of the edge band + 2 mm.
- Move the guide plate (8.1) as close as possible to
the cutter by loosening the rotating knob (8.3).
- Adjust the depth of the guide plate with the
adjusting wheel (8.2) so that during trimming
a few decimillimetres of the edge band are left
protruding which can then be sanded down by
hand.
The chip guard SF-OF (7.2), available as an ac-
cessory, improves dust extraction when trimming
edge bands. It is fastened to the side of the platen
with the rotating knob (7.1) and cover the cutter
from above during work (Fig. 8).
7 Accessories
For your own safety, use only original
Festool accessories and spare parts.
Festool offers extensive accessories that enable
you to use your machine effectively for a wide
variety of applications, e.g.: routing circle, guide
rails with rows of holes, routing aid, router base
for bench-mounted use.
The accessory and tool order number can be found
in the Festool catalogue or on the Internet under
„www.festool.com".
8 Maintenance and care
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
All maintenance and repair work which
requires the motor casing to be opened
may only be carried out by an authorised
service centre.
Always keep the machine and the ventilation slots
clean.
The tool is fi tted with special motor brushes with
an automatic cut-out. When the brushes become
worn the power supply is shut off automatically
and the tool comes to a standstill.
9 Disposal
Do not throw the power tool in your household
waste! Dispose of machines, accessories and
packaging at an environmentally-responsible
recycling centre. Observe the valid national regu-
lations.
EU only: European Directive 2002/96/EC stipulate
that used electric power tools must be collected
separately and disposed of at an environmentally
responsible recycling centre.
10 Warranty
Our equipment is under warranty for at least 12
months with regard to material or production
faults in accordance with national legislation.
In the EU countries, the warranty period is 24
months (an invoice or delivery note is required
as proof of purchase). Damage resulting from, in
particular, normal wear and tear, o-verloading,
improper handling, or caused by the user or other
damage caused by not following the operating
instructions, or any fault acknowledged at the
time of purchase, is not covered by the warranty.
Damage caused by the use of non-original ac-
cessories and consumable material (e.g. sanding
pads) is also excluded.
Complaints will only be acknowledged if the
equipment has not been dismantled before be-
ing sent back to the suppliers or to an author-
ised Festool customer support workshop. Store
the operating instructions, safety notes, spare
parts list and proof of purchase in a safe place.
In addition, the manufacturer's current warranty
conditions apply.
Note
We reserve the right to make changes to the tech-
nical data contained in this information as a result
of ongoing research and development work.
11 EU Declaration of Conformity
Router
OF 1010 Q
OF 1010 EQ
OF 1010 EBQ
Year of CE mark: 2000
We declare under sole responsibility that this
product complies with the following norms or
normative documents:
EN 60745-1, EN 60745-2-17, EN 55014-1, EN
55014-2, EN 61000-3-2, EN 61000-3-3 in accord-
16
Serial no.
490108
491991
490174