Honeywell V8043C Guide Rapide

APPLICATION:
The V8043 Motorized Zone Valve provides two-position
(open-close) control of supply water for baseboard radiation,
convectors, fan-coil units, etc. It uses a two-wire, 24-volt con-
trol circuit and requires a SPST thermostat. Integral end-switch
models permit the sequencing of auxiliary equipment.
FEATURES:
• Quiet, dependable operation is provided by motor-operated
powerhead and swing-type ball valve.
• Unique rotating ball plug that seats on a different part of its
surface on each closing.
• Closes against the flow of water to assure quiet operation.
• Manual opener moves ball away from seat allowing valve
to be installed without disassembly.
• Manual operation on power failure.
• Easy servicing because the entire powerhead assembly can
be replaced without removing valve body from line. Op-
tional accessory fittings can be provided to facilitate con-
venient removal of the entire zone valve unit.
• Low power requirements allow four valves to be operated
from a single 40 VA transformer.
• Integral end-switch on F & G models to permit sequencing
of auxiliary equipment.
• Choice of sweat, female NPT and flare (with union-flare
adapters) body styles.
• Compact construction permits fitting under cover of
most baseboards,
SPECIFICATIONS:
MODELS:
V8043C - Normally closed
V8043D - Normally open
V8043F - Normally closed with integral line voltage end
switch
V8043G - Normally closed with integral low voltage end
switch
BODY STYLES:
All models have straight through pattern only.
1/2", 3/4" or 1'' sweat or female NPT, or 3/8" flare.
Inlet fittings can be provided with or without 1/16''
diameter bypass or bleed.
CLOSE-OFF WATER PRESSURES AND CAPACITY (CV)
RATINGS:
All models - 50 psi for 1.0 Cv
20 psi for 3.5 Cv (Standard Rating)
8 psi for 8.0 Cv
STATIC PRESSURE RATING:
Both 125 psi (VC8043C/D/F/G1000 series) and
300 psi (V8043C/D/G3300 series) models available
TEMPERATURE RATING:
o o
Liquid - 4 C to 93 C (40
Ambient - 4 o C to 52 o C (40
Steam - Consult your local Honeywell representative
WIRING CONNECTIONS:
'C' and 'D' Models - 2 low voltage 0.5 m (18 in.) leadwires
with strain relief
'F' Tradeline Model - 5 screw terminal board. Includes
'blind' terminal for transformer and thermostat wiring
convenience. (See Fig. 4) It Also includes add-on line
voltage enclosure with conduit opening for end switch
wiring.
'G' Model - 4 low voltage 0.5 m (18 in.) leadwires with
strain relief.
POWER REQUIREMENTS AND TIMING:
All models - 24 V, 50/60 Hz (cycles) 6 W nominal, 15
seconds to open, and 4-5 seconds to close.
Order transformer separately. See alternate selection.
www.honeywell.ca/water-controls/
o o
F to 200 F)
o F to 125 o F)
V8043C, D, F & G
MOTORIZED ZONE VALVES
V8043C, D
V8043G
TRANSFORMER:
All models - AT72 or AT20B (maximum of 4 valves per
AT72 or 2 valves per AT20B).
Order transformers separately.
AUXILIARY SWITCH RATINGS:
'G' Model - 50 VA pilot duty at 24 Vac
'F' Model - 4.4 Amps running at 120 Vac
RECOMMENDED WALL THERMOSTATS:
Heating Only - T86A, T822D:
(T822C for normally open [N.O.] valves)
Cooling Only, or Heating-Cooling - T87F with Q539
THERMOSTAT HEATER SETTING:
For Heat Anticipation: 0.32 Amps
REPLACEMENT POWERHEADS:
125 psi Models:
'C' Model - P/N 40003916-011
'D' Model - P/N 40003916-014
'G' Model - P/N 40003916-012
'F' Model - P/N 40003916-013
REPLACEMENT MOTOR:
24 Vac, 50/60 Hz Models - P/N 272748AB
24 Vac, 50/60Hz, Plated Motor - P/N 272748ABP
REPLACEMENT END SWITCH:
Old Style (prior to 1978) requiring metal bracket
- P/N 272744A
New Style - P/N 272744B
REPLACEMENT 0-RING: P/N 272756A
NOTE
The standard valve is not recommended for steam service.
Consult you local Honeywell representative whenever steam
applications are involved.
ACCESSORIES:
Flare-to-Sweat Union Adapters (sold in sets of 2)
3/8 Flare to 1/2 Sweat - P/N 272704A
3/8 Flare to 3/4 Sweat - P/N 272704B
Residential & Building Controls Group
V8043F
272704A
95C-10002B-1