Publicité

Liens rapides

sauder.com
Entertainment Credenza
Edge Water Collection | Model 409048
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
Entertaining what
entertains you.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-26
Français pg 27-29
Español pg 30-32
Lot # 387023
11/19/15
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987

Publicité

Table des Matières
loading

Sommaire des Matières pour Sauder 409048

  • Page 1 Edge Water Collection | Model 409048 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. Need help? Visit Sauder.com to view video assembly tips or chat with a live rep. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Prefer the phone? Call 1-800-523-3987.
  • Page 2 • Check the size and weight of your TV. Compare it to the diagram below – before you begin assembly! • This Sauder unit is designed for use with televisions weighing less than 95 pounds. Never use with a TV that weighs more.
  • Page 3: Part Identifi Cation

    STOP MOLDING (1) LEFT UPRIGHT (1) LEG (2) RIGHT DRAWER SIDE (1) TOP (1) VALANCE (1) LEFT DRAWER SIDE (1) BOTTOM (1) DRAWER FRONT (1) DRAWER BACK (1) SHELF (1) SPACER (2) D701 DRAWER BOTTOM (1) D701 www.sauder.com/services 409048 Page 3...
  • Page 4 Surface will be damaged. 02/ 02 269227 (Refer to Step 20 for proper location and application) RUBBER NAIL - 42 METAL PIN - 20 GROMMET CAP - 1 GROMMET - 1 SLEEVE - 20 Page 4 409048 www.sauder.com/services...
  • Page 5: Table Des Matières

    12S BROWN 1" FLAT HEAD SCREW - 4 16S BLACK 1-7/8" PAN HEAD SCREW - 2 30S BLACK 1-9/16" FLAT HEAD SCREW - 4 BLACK 1-1/8" MACHINE SCREW - 2 BLACK 7/8" MACHINE SCREW - 2 www.sauder.com/services 409048 Page 5...
  • Page 6 fl oor. Scan this QR code or go to this address: http://qr.sauder.com/?ID=1338 To begin assembly, push a SAUDER TWIST-LOCK® å to watch a video on how to assemble your unit. FASTENER (7F) into the large holes in the RIGHT END (A) and LEFT END (B).
  • Page 7 Push eight HIDDEN CAMS (1F) into the ENDS (A and B) å and TOP (E2). Do not tighten the HIDDEN CAMS in this step. Arrow Arrow Arrow Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board. www.sauder.com/services 409048 Page 7...
  • Page 8 Step 3 Turn eight CAM SCREWS (8F) into the LEGS (K2) and å STOP MOLDING (XX). Remember: Righty tighty. Lefty loosey. Page 8 409048 www.sauder.com/services...
  • Page 9 Fill the holes 1/4 to 1/2 full with GLUE. insert into the holes in the edge of the TOP. Wipe away the excess GLUE. Caution (5 used) Inspect the parts thoroughly before assembling. Disassembly of glued parts is extremely diffi cult. Seam www.sauder.com/services 409048 Page 9...
  • Page 10 Fasten the FEET (Y) to the LEGS (K2). Use two BLACK å 1-7/8” PAN HEAD SCREWS (16S). These surfaces should be even. These surfaces should be even. BLACK 1-7/8" PAN HEAD SCREW (2 used in this step) Page 10 409048 www.sauder.com/services...
  • Page 11: Gold 5/16" Flat Head Screw

    LEFT (35DB) to the UPRIGHTS (C and D). Use four GOLD 5/16" FLAT HEAD SCREWS (3S) through holes #1 and #3. Finished edge GOLD 5/16" FLAT HEAD SCREW (4 used in this step) Roller end Finished edge Roller end www.sauder.com/services 409048 Page 11...
  • Page 12 Step 7 Fasten the SHELF (G) to the UPRIGHTS (C and D). å ® How to use the SAUDER TWIST-LOCK FASTENER Tighten four TWIST-LOCK® FASTENERS. 1. Insert the dowel end of the FASTENER into the hole of the adjoining part.
  • Page 13 S u r - L O I S T E R S T E N F A S S u r f a c H I D i t h D E N www.sauder.com/services 409048 Page 13...
  • Page 14 These holes must be here. S u r f a c i t h I S T - L O F A S T E N ® E R S BLACK 1-7/8" FLAT HEAD SCREW (4 used in this step) Page 14 409048 www.sauder.com/services...
  • Page 15 Fasten the RIGHT END (A) to the TOP (E2) and å BOTTOM (F). Tighten four TWIST-LOCK® FASTENERS. i t h o ® f a c S u r - L O I S T E R S T E N F A S www.sauder.com/services 409048 Page 15...
  • Page 16 Use four BLACK 9/16" LARGE HEAD SCREWS (1S). Fasten the VALANCE (L) to the TOP (E2). Use two BLACK å 9/16" LARGE HEAD SCREWS (1S). Curved edge BLACK 9/16" LARGE HEAD SCREW Curved edge (12 used in this step) Page 16 409048 www.sauder.com/services...
  • Page 17 UPRIGHTS (C and D). NAIL NOTE: Perforations have been provided for access through the å (42 used in this step) BACK. Carefully cut out the holes needed. These holes must line up over the UPRIGHTS (C and D). www.sauder.com/services 409048 Page 17...
  • Page 18: Brown 1" Flat Head Screw

    Fasten the SPACERS (R) to the BOTTOM (F). Use four å BROWN 1" FLAT HEAD SCREWS (12S). Push the PLASTIC FEET (23E) into the holes in å the SPACERS (R). BROWN 1" FLAT HEAD SCREW (4 used in this step) Page 18 409048 www.sauder.com/services...
  • Page 19 Step 14 Fasten two HINGES (14H) to each DOOR (I). Use eight å BLACK 1/2" FLAT HEAD SCREWS (11S). BLACK 1/2" FLAT HEAD SCREW (8 used in this step) www.sauder.com/services 409048 Page 19...
  • Page 20: Black 1-1/8" Machine Screw

    FELT DISC on the DOOR where it comes in contact with the RIGHT UPRIGHT (C). Mounting screw Repeat this step for the other DOOR (I). å Hinge BLACK 1-1/8" MACHINE SCREW (2 used in this step) Page 20 409048 www.sauder.com/services...
  • Page 21 To adjust the DOORS in or out (depth), loosen the mounting screw one turn and move the å DOORS in or out, as needed. Tighten the mounting screw after making adjustments. Mounting screw (depth) Adjusting screw (horizontal) (vertical adjustment) www.sauder.com/services 409048 Page 21...
  • Page 22: Black 1-9/16" Flat Head Screw

    Fasten the DRAWER BACK (D62) to the DRAWER SIDES (D12 and D13). Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S). å NOTE: Be sure the DRAWER BOTTOM (D701) inserts into the groove of the DRAWER BACK (D62). å Page 22 409048 www.sauder.com/services...
  • Page 23 SLIDE. Screw head - turn the CAM Roller end to line up holes in SLIDES with holes in DRAWER SIDES. Roller end GOLD 5/16" FLAT HEAD SCREW (4 used for the SLIDES) www.sauder.com/services 409048 Page 23...
  • Page 24 Step 19 Fasten the KNOBS (17K) to the DRAWER FRONT (M). Use two å BLACK 7/8" MACHINE SCREWS (37S). BLACK 7/8" MACHINE SCREW (2 used for the KNOBS) Page 24 409048 www.sauder.com/services...
  • Page 25 - The base of the TV must be able to sit completely on this shelf. 95 lbs. 25 lbs. 25 lbs. 25 lbs. 30 lbs. 25 lbs. 15 lbs. 25 lbs. 50 lbs. total (20 used) www.sauder.com/services 409048 Page 25...
  • Page 26 #3. The higher the screw in the oblong hole, the higher your drawer front will be. The lower the screw, the lower the drawer front. Page 26 409048 www.sauder.com/services...
  • Page 27: Meuble Télévision/Vidéo/Stéréo

    Modèle 409048 Meuble Télévision/Vidéo/Stéréo Utilisez les instructions d’ a ssemblage en français avec les NOUS SOMMES LA POUR VOUS AIDER! schémas étape par étape du manuel d’instruction en anglais. Nous faisons de notre mieux pour nous assurer que votre meuble Chaque étape en français correspond à...
  • Page 28 Fixer les MONTANTS (C et D) au DESSUS (E2). Serrer quatre Pour commencer l’ a ssemblage, enfoncer une FIXATION TWIST-LOCK® SAUDER (7F) FIXATIONS TWIST-LOCK®. dans les gros trous de l’EXTRÉMITÉ DROITE (A) et l’EXTRÉMITÉ GAUCHE (B).
  • Page 29 3 Fixer l'ARRIÈRE DE TIROIR (D62) aux CÔTÉS DE TIROIR (D12 et D13). Utiliser quatre VIS TÊTE PLATE 40 mm NOIRES (30S). REMARQUE : S'assurer que le FOND DE TIROIR (D701) s'encastre dans la rainure de l'ARRIÈRE DE TIROIR (D62). www.sauder.com/services 409048 Page 29...
  • Page 30: Lista De Partes

    Modelo 409048 Centro de Entretenimiento Use estas instrucciones de ensamblaje en español junto con las ESTAMOS AQUI PARA AYUDAR! fi guras paso-a-paso provistas en el folleto inglés. Cada paso Tratamos de asegurar que su mueble llega en condición excelente. en español corresponde al mismo paso en inglés. Se destacan Nuestros representantes de Servicio al Cliente son amables y las fi...
  • Page 31 Fije los PARALES (C y D) al PANEL SUPERIOR (E2). Apriete cuatro SUJETADORES TWIST-LOCK®. Para comenzar el ensamblaje, empujun SUJETADOR TWIST-LOCK® SAUDER (7F) dentro de los agujeros grandes del EXTREMO DERECHO (A) y del EXTREMO IZQUIERDO (B). PASO 9 Repita este paso para los PARALES (C y D), el FONDO (F) y el ESTANTE (G).
  • Page 32 3 Fije el DORSO DE CAJÓN (D62) a los LADOS DE CAJÓN (D12 y D13). Utilice cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 40 mm (30S). NOTA: Asegúrese que el FONDO DE CAJÓN (D701) ajuste dentro de la ranura del DORSO DE CAJÓN (D62). Page 32 409048 www.sauder.com/services...
  • Page 33 équipé. • Blessure physique. Le mobilier peut être très lourd. • Ne pas pousser le mobilier, surtout sur la moquette. Se faire aider par une autre personne pour soulever l’élément et le mettre en place. www.sauder.com/services 409048 Page 33...
  • Page 34 • Lesión física. El mobiliario puede ser • No empuje la unidad, especialmente muy pesado. sobre un piso alfombrado. Pide la ayuda de otra persona en levantar la unidad y colocarla en lugar. Page 34 409048 www.sauder.com/services...
  • Page 35: Garantie Limitée De 5 Ans

    GARANTIE LIMITÉE DE 5 ANS 1. Sauder Woodworking Co. (Sauder®) off re une couverture de garantie limitée à l’ a cheteur 4. La présente garantie ne s’ a pplique qu’ a ux défauts garantis qui se produisent pour initial du présent produit pendant une période de cinq ans à...
  • Page 36 Dear Valued Customer: So, how did it go? Thanks so much for choosing Sauder® furniture. I hope the Set a world record for speed? purchase and assembly process was a positive experience Feeling good about yourself? and you feel good about the furniture you just built. If you Nice.

Table des Matières