Progress Lighting P86-TG Instructions De Montage Et D'installation

7
12
13
FIG.2
10
11
6
20
1
20
FIG.3
9
3
18
v
21
13
P8587-01
15
16
17
19
FIG.4
16
13
23
15
FIG.1
11
9
24
14
22 16
4
FIG.6
WHITE SUPPLY WHITE OR IDENTIFIED
WIRE FIXTURE WIRE
UL LISTED
WIRENUTS
BLACK SUPPLY PLAIN OR BLACK
WIRE FIXTURE WIRE
BARE, OR GREEN BARE, OR GREEN
GROUND WIRE FIXTURE GROUND
FROM SUPPLY WIRE
FIG.5
PAGE 4 of 4
SPEC.NO. 023806
8
WARNING: When using special control devices with this fixture, follow instructions carefully to ensure N.E.C.
compliance. For more help, contact a qualified electrical contractor.
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects
and/or other reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise
touching this product.
CAUTION: To complete the installation, choose only UL listed Progress trims from the label inside the
housing. The use of any trim not listed in this fixture is a violation of N.E.C. article 110-3(B) and voids all
warranties.
FOR I.C. APPLICATIONS where the fixture may be in direct contact with insulation, remove the peel off
warning label (1) from the housing (3) that reads: "WARNING RISK OF FIRE, DO NOT INSTALL INSULATION
WITHIN 3 INCHES OF THE SIDES OF THE HOUSINGS".
FOR NON-I.C. APPLICATIONS where, except for mounting points, the fixture is installed at least ½" from any
combustible surface and insulation is a minimum of 3 inches from all sides, do not remove Warning Label (1)
from Housing (3).
14
Follow this instruction sheet carefully. Be sure electricity is OFF before starting installation.
1. For Wooden Joists: Use the Centering Notches (4) located on the Plaster Frame (13) to position the Fixture.
Extend the Bar Hangers (6), use joist alignment tabs to locate fixture. Drive the 4 Nails (7) into Joists (8) (Fig.
1) to secure Housing (3). Drive additional nails through holes in Bar Hanger for alternate support if required.
2. For Suspended Ceilings: Place the Fixture on the ceiling grid with the "T" Bars (9) running through the Bar
Hanger Notches (10). Using a flat head screwdriver or other tool, bend the integral t-bar mounting tabs (11)
downward to a vertical position (Fig. 3). Secure housing to support structure with tie wire (supplied by others)
in the holes supplied. Sheetmetal screws (supplied by others) can also be used in the holes supplied (20).
3. Locate Housing along Bar Hanger in desired position and, using pliers, squeeze the 4 Locking Tabs (12) on
the Plaster Frame (13) tightly over the Bar Hangers to prevent further Housing movement. Bar Hangers (6)
may be installed in alternate Slots (23) if mounting conditions require.
4. As desired, hanger bars (6) may be shortened at score mark to fit tight mounting conditions and joist
alignment tabs removed to adjust vertically as needed by breaking off with pliers.
5. Unsnap Junction Box Cover (14) by lifting the Leaf Spring (24).
6. Run supply wires through UL Listed connectors (not supplied) in one of the five Pryouts (15) on the Junction
Box (16) or Type NM cable (ROMEX) through an Opening above the Wire Retaining Plate (17). Connect
Supply Wires (19) as shown in Fig 4 & 5. Replace Cover.
7. FOR AIR-TIGHT APPLICATIONS: This Progress product is Air-Tight approved per ASTM E283 testing
standards and complies with Washington State Energy Code Requirements. To complete the installation of
this Air-Tight product, the opening between the housing (3) and drywall ceiling (22) must be sealed by the
installer using silicone caulking, tape, or any other means acceptable to the local codes official. Progress
Lighting Gasket Accessory Kit P8587-01 (purchased separately) can be used for this purpose (Fig. 6).
8. Loosen Screws (21) to adjust Housing (3) for variations in ceiling thickness. Bottom of Housing should be
flush with ceiling (22) within tolerance.
9. Select a Trim from the Wattage Label inside the Housing. Use Only Lamp Types approved for the Trim
chosen. DO NOT EXCEED MAXIMUM LISTED WATTAGE(S)! For trim installation, refer to trim installation
instructions.
INSTRUCTION SHEET MUST BE REMOVED FROM FIXTURE PRIOR TO ENERGIZING.
(09/06/12) Rev. B
Assembly & Installation Instructions
CAUTION: Read instructions carefully and turn electricity off at main
circuit breaker panel before beginning installation.
P86-TG
PAGE 1 of 4
SPEC.NO. 023806 (09/06/12) Rev. B