Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
LED LIGHT
WARNING : Don't stare at the LED light,
nor put the light illuminates people eyes .
If eyes focus on the light for a while, may
cause pains .
1 . Equipped with a LED light
indicated the front of bits .
2 . Light can be on with slightly
pressing the trigger . (Fig . 7A)
3 . The LED light will be turned off
automatically after the tool is
stopped by 15 seconds
•
BELT HOOK
CAUTION : When installing the hook,
tighten the screw firmly. Failure to do so
may cause the breakage of the tool or
personal injury .
4.
The belt hook is convenient for
temporarily hanging the tool . This
can be installed on either side of the
tool .
5.
To install the belt hook, insert it into a
groove in the tool housing on either
side and then secure it with a screw .
To remove, loosen the screw and
then take it out . (Fig . 8A & Fig . 8B)
6.
After installing the belt hook, make
sure that it is screwed firmly.
•
ATTACHING AND REMOVING
ACCESSORIES
5.
Use the sockets designed for
power tools or pneumatic tools.
6.
Use only the appropriate size
Square Drive Sockets .
7.
To attach a socket, align the
accessory with the anvil and
push it firmly over the retaining
ring . (Fig . 9A)
8.
To remove the accessory, pull
the accessory off the anvil .
(Fig . 9B)
www.swstahl.de
www.swstahl.de
18
LED Light
Fig. 7
Fig. 8A
Fig. 8B
Fig. 9A
Fig. 9B
SW-Stahl GmbH
SW-Stahl GmbH
An der Hasenjagd 3
An der Hasenjagd 3
D-42897 Remscheid
D-42897 Remscheid
MAINTENANCE INFORMATION
WARNING : Always be sure that the tool
is switched off and battery is removed
before attempting to perform inspection
or maintenance on the tool . Failure to
switch off and remove the battery may
result in serious personal injury from
accidental start-up .
•
CLEANING
Remove the battery
1 . Keep the air vents free of obstructions . Do not spray,
wash, or immerse the air vents in water .
2 . Wipe off the housing and the plastic components using a
moist, soft cloth. Do not use strong solvents or detergents
on the plastic housing or plastic components . Certain
household cleaners may cause dam age, and may cause
a shock hazard .
•
MAINTENANCE
1 . Place switch in OFF position and remove the battery
before the appliance is serviced, cleaned, or maintenance
is performed .
2 . Check if device loose, parts damaged such .
3 . Please storage locked tools in dry location where the
children cannot touch when you didn't use tool .
4 . Only use recommended spare parts and accessories from
manufacturer for replacement .
5 . Before and after using, check and maintain tools
regularly. Fix tool via our authorized center .
6 . Keep hands dry, clean and no greasiness and lubricant .
7 . Please don't install battery pack into tool when storage .
WARNING : Always wear safety goggles
or safety glasses with side shields when
operating tool . Failure to do so could
result in objects being thrown into your
eyes, resulting in possible serious injury .
WARNING : Read all instructions Failure
to follow all instructions listed below may
result in electric shock, fire and/or serious
injury. The term "power tool" in all of the
warnings listed below refers to your
mains-operated corded) power tool or
battery-operated (cordless) power tool .
Tel. +49 (0) 2191 / 46438-0
Tel. +49 (0) 2191 / 46438-0
Fax +49 (0) 2191 / 46438-40
Fax +49 (0) 2191 / 46438-40
E-Mail: info@swstahl.de
E-Mail: info@swstahl.de
S3300
S3300
Publicité
Table des Matières
