Charging The Battery Pack; Battery Capacity Indicator - SW-Stahl S3300 Mode D'emploi

NOTE: Do not use force when installing the battery pack . If the cartridge
does not slide in easily, it is not being inserted correctly .
•

CHARGING THE BATTERY PACK

Cracked
The battery pack for this tool is
1.
supplied in a low charge condition
to prevent possible problems,
therefore, you have to charge the
battery before first use
2. Charge battery pack only with
the charger provided
3. Using an other charger can
cause severe damage or even cause battery to explode
from the work piece and determine the reason for jamming .
4. Connect the charger to a power outlet . Place the battery
pack in the charger aligning raised rib on the battery pack
with the groove in the charger . (Fig . 2)
NOTE:
• Lithium battery does not have memory effect, there-
fore to prolong the battery life please fully charged the
battery before storage . This will reduce battery self
discharging characteristics . If the voltage of the battery is
too low, it'll automatically lock itself . If the tool feels lack of
power, please stop the operation and charge the battery
immediately . If the battery is stored more than 3 months,
please charge the battery first before operation.
• If the tool does not function, please clear all debris and
restart again . If malfunction continues malfunctions, please
remove the battery immediately and contact the local
service dealers for assistance
• The battery pack will become slightly warmer while
charging. This is normal and does not indicate a problem .
• Do not place charger in an environment either extreme hot
or cold . It will work best at normal room temperature .
• When the battery is fully-charged, unplug your charger from
the power supply and remove the battery pack from the
charger .
CAUTION : To prevent damage to the
battery pack, remove the battery pack
immediately from the charger when no
charger LED lights . Return battery pack
and charger to your dealer for checking
or replacing . Do not insert a battery pack
into a damaged charger, it may damage
your battery pack.
www.swstahl.de
www.swstahl.de
16
DANGER : If battery pack
case is cracked or
damaged, do not insert into
charger . Danger of electric
shock or electrocution
.
Fig. 2
SW-Stahl GmbH
SW-Stahl GmbH
An der Hasenjagd 3
An der Hasenjagd 3
D-42897 Remscheid
D-42897 Remscheid
•

BATTERY CAPACITY INDICATOR

1. The tool is applied with the
battery capacity indicator (A)
on the top pad for easy view .
(Fig . 3)
2. The remaining battery power
is shown as lights by three
alphabetic symbols when the
trigger pressed; when the
trigger released, the button
stays lighted is shown the speed mode the tool performs
and will last approximately 60 seconds .
3. Either the indicator light blinks or none indicator lights, the
battery capacity has run out, so the tool does not operate .
In these cases, charge the battery or replace the dead
battery by a fully-charged on .
When two or more indicator lights do not light even after
4.
charging is complete, the battery has reached the end of its
service life .
INDICATOR LIGHTS
Lighted OFF
≥ 60% 30~60%
NOTE:
• The indicated capacity may be lower than the actual level
during use of the tool .
• Depending on the conditions of use and the ambient
temperature, the indication may differ slightly from the actual
capacity .
CHARGER LED INDICATION
•
NOTE: The battery will not reach full charge after the first charge .
Allow several cycles (drilling followed by recharging) for them
to become fully charged
Tel. +49 (0) 2191 / 46438-0
Tel. +49 (0) 2191 / 46438-0
Fax +49 (0) 2191 / 46438-40
Fax +49 (0) 2191 / 46438-40
E-Mail: info@swstahl.de
E-Mail: info@swstahl.de
S3300
S3300
A
Fig. 3
Blinking
≤ 10%
Malfunction
(Charge the
≤ 30%
battery)