Table des Matières
Publicité
Page 7 of 19
•
OFFER THE ASSEMBLY TO THE ORIGINAL MOUNTING POINTS ON THE OEM TAIL UNIT
WHILE FEEDING ALL THE WIRING (INDICATORS AND LICENCE PLATE ILLUMINATOR WIRES)
THROUGH THE ORIGINAL HOLE ON THE OEM TAIL UNIT AND SECURE IN POSITION.
•
IF FITTING THE ORIGINAL INDICATOR, CONNECT THEM TO THE SUB HARNESS AS
ORIGINAL, IF FITTING R&G MINI'S CONNECT TO THE SUB HARNESS USING THE SUPPLIED
CONNECTORS (ITEM 11).
•
FROM THE KIT, TAKE THE HEAT SHRINK TUBE (ITEM 16) AND CUT IT TO A SUITABLE
LENGTH. FEED BOTH WIRES FROM THE LICENCE PLATE ILLUMINATOR (ITEM 9) THROUGH.
PLEASE LEAVE AT LEAST 25mm OF WIRES EXPOSED FROM THE TUBE. USING A SUITABLE
HEAT SOURCE, SHRINK THE HEAT-SHRINK TUBE.
•
FROM THE KIT, USE THE LICENCE PLATE ILLUMINATOR CONNECTOR (ITEM 12) TO
CONNECT TO THE LICENCE PLATE ILLUMINATOR TO THE OEM SUB-HARNESS. IF LIGHT
FAILS TO ILLUMINATE, PLEASE SWAP THE BULLET CONNECTORS OVER.
•
RECONNECT THE MAIN SUB-HARNESS MALE CONNECTOR TO THE OEM FEMALE
CONNECTOR IN MAIN HARNESS AS ORIGINAL.
•
IT IS ADVISABLE TO CHECK OPERATION OF ALL LIGHTS AT THIS STAGE.
•
TIDY UP THE WIRING USING THE CABLE TIES AND SELF-ADHESIVE CLIPS (ITEMS 13 and
18) PROVIDED.
•
REFIT LICENCE PLATE (IT MAY REQUIRE DRILLING).
•
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN
ON THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE
PLATE HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS
IN THE ROAD. IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY
AND TAKE AVOIDING ACTION. FAILURE TO CHECK THIS COULD RESULT IN
SERIOUS INJURY.
•
REFIT SEAT.
•
DEPENDING ON LOCAL LAWS, ATTACH ENCLOSED RED REFLECTOR (ITEM 17) IN AN
APPROPIATE LOCATION.
•
TEST THE INDICATORS (TURN SIGNALS), LICENCE PLATE ILLUMINATOR AND ALL LIGHTS
BEFORE RIDING.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products ot her
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and
suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and
care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that
the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its
option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or
used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the
defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death
and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross
value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to
faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 1
28/09/2020
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
R&G
(NSY)
www.rg-racing.com
Email:
LP0202
info@rg-racing.com
Publicité
Table des Matières
