Accessories; Environmental Protection; Technical Specifications - Metabo S 18 LTX 115 Instructions D'utilisation Originales

en ENGLISH

11. Accessories

Only use original Metabo battery packs and Metabo
accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Batter chargers: ASC Ultra, ASC 30-36, etc.
Battery packs with different capacities. Use
battery packs only with voltage suitable for your
power tool.
Order no.: 6.25346 ... 3.5 Ah (LiHD)
Order no.: 6.25342 ... 5.5 Ah (LiHD)
Order no.: 6.25345 ... 7.0 Ah (LiHD)
etc.
Order no.: 6.25591 .... 4 Ah (Li-Ion)
Order no.: 6.25592 .... 5.2 Ah (Li-Ion)
etc.
Fleece/sanding sleeves
Grinding wheel
Round wire brushes
Expansion rollers
Polishing rings
Auxiliary materials for polishing
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to power tools must only be carried
out by qualified electricians!
If the connection lead is damaged, it must be
replaced by a special connection lead.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

The generated sanding dust may contain harmful
substances: dispose of appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
tools, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! In
accordance with European Directive 2012/
19/EU relating to electrical and electronic waste
and implementation of national law, used electrical
tools must be collected separately and disposed of
in an environmentally friendly manner at recycling
centres.
Special notes regarding cordless machines:
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
16
Do not allow battery packs to come into contact with
water!
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).

14. Technical Specifications

Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
D = Permitted wheel diameter
B = maximum wheel width
max
M = Spindle thread
l = Length of spindle
n* = No-load speed (maximum speed)
U = Voltage of battery pack
P = Rated input power
1
P = Power output
2
m = Weight with smallest battery pack/weight
without cord
Measured values determined in conformity with EN
60745.
Direct current (cordless machines)
~
Alternating current (mains powered machines)
Machine in protection class II (mains powered
machines)
* SE 17-200 RT: High-energy, high-frequency
interferences can cause speed fluctuations. The
fluctuations disappear, however, as soon as the
interference fades away.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods for assessment
purposes when the load is lower. Arrange protective
measures for the user, such as organisational
measures based on the adjusted estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 60745:
a = Vibration emission value (polishing)
h, P
K =Uncertainty (vibration)
h,P
Typical A-weighted sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K =Uncertainty
pA WA
Wear ear protectors!