Hella 2NE 959 011-5 Serie Instructions page 2

INSTRUCTION SHEET
2NE 959 011-5xx
for:
Lamp Mounting
1/4" Ø nut, bolt and washer have been supplied with this product. Do not mount the lamp where damage is
likely to be sustained due to tie-downs and other securing devices.
Lamp should be mounted on a flat surface. Drill one mounting hole between 6.5mm and 8mm in diameter.
A small 5mm location hole is also recommended to assist in mounting the lamp accurately and to stop the
lamp from rotating during or after installation. This can be done using the location pin supplied*.
If passing the cable through a hole, ensure there are no sharp edges to cut or chafe the cable.
Drill a cable exit hole 6mm diameter in the position as shown on diagram below.
Ensure the lens engraving "TOP" is located correctly.
Connect lamp wiring as per chart below.
Try to keep the cable as long as possible, preferably join the cable inside a
sealed cable junction box.
*location pin not supplied with all lamp models
General Dimensions (mm)
74
Reference axis
11.5
Cable Exit
CABLE EXIT
Wiring Colour Coding
This lamp is Multivolt capable allowing full light output between 9 and 33 volts.
LED modules are polarity conscious. Reverse polarity will not damage this product but will inhibit its function.
HELLA recommends wire connections be soldered, and heat shrink tubing applied to seal the joint.
Colour Connect to Power Consumption
White/Black Negative (-) -
Yellow Rear Fog (+) 3 watts
NB: Lamp must be protected by a fuse rated at 5 amperes maximum.
optional
location Pin
1/4" bolt/nut
cable exit
83 10 41
21
optional 4mm Ø
TOP
location pin
(removable)
9010
6.3 (1/4") bolt
FRONT SIDE
Important Notes for Installer and
Vehicle Owner
Introduction
LED signal and marker lamps offer many advantages over conventional bulb lamps. Significantly reduced
power consumption, ultra long life and high tolerance to shock and vibration make the LED lamps the ideal
choice for the commercial transport industry, where the cost of ownership versus the initial purchase price
of the product is well understood.
Compatibility to existing electrical systems
It is important for the installer to ascertain the compatibility of the low power consumption LED lamps with
the electrical and/or electronic systems of the complete vehicle, including trailers. In most cases the reduced
power consumption is beneficial by imposing less demands on the entire electrical system.
For certain functions some electrical systems rely on a set power consumption for monitoring whether, for
example, a trailer is connected.
Operation of this lamp using alternating current or modulated direct voltage will cause premature light failure.
HELLA recommends connecting ADR or ECE certified Multivolt LED signal and marker lamps to a continuous
(unmodulated) 12V or 24V power supply to ensure safe light operation.
Electromagnetic Compatibility (EMC)
This LED lamp in an electronic device. The electrical circuits contain components that suppress possible
interference, both emission as well as susceptibility, to the limits prescribed in UNECE Vehicle Regulation
No. 10.
To avoid false signals or interference, it is standard practice that sensitive instrumentation such as ABS and
Tachometers etc. are provided with direct earths.
Protection against damage due to voltage spikes
This LED lamp is protected against damage from positive voltage spikes caused by events such as load
dump conditions up to severity level 3 of ISO 7637-2 and contains a Transient Voltage Suppressor (TVS)
designed to withstand a pulse of up to 5000 Watts.
The lamp is protected against reverse polarity connection and negative voltage spikes of up to 1000 volts.
Electric Welding
Electric Welding may damage the LED lamps. For LED lamps, HELLA recommends the negative connection to
be wired isolated from the vehicle chassis. If the lamp uses the chassis as the earth return it is recommended
that this earth return is disconnected during electric welding.
FIT AND FORGET - BY DESIGN
Congratulations, the product you have selected comes from HELLA - a world leader in LED
lighting design.
Following the launch of the first LED automotive signal lamps in 1990, HELLA Design and
Innovation continues to set new standards. HELLA innovative solutions have been incorporated into
millions of lamps, engineered and tested to the most stringent standards, to suit the most demanding
environmental conditions.
The cornerstone to the success of our products is our no compromise Fit and Forget - by Design
philosophy which is incorporated into every step of the product life cycle.
In a world consuming finite resources at an ever faster rate, Fit and Forget - by Design is the right
environmental choice that also makes perfect economic sense to customers that consider the total life
cycle Cost of Ownership.
For general comments about HELLA's products please contact us on E-mail at techfeedback@hella.co.nz