Maintenance; General; Daily Cleaning; Weekly Cleaning - Ovention Matchbox M1313 Manuel D'installation

MAINTENANCE

General

Ovention matchbox Ovens are designed for maximum
® ®
durability and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAzARD:
• Turn off Standby switch, allow unit to cool, and unplug
unit/turn OFF Main
performing any cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not clean unit with metal scouring pads. Metal
pieces can break off pad and touch electrical
components, creating risk of electric shock.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Ovention Replacement Parts when
service is required. Failure to use Genuine Ovention
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Ovention Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Ovention equipment.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Ovention Service
Agent or contact the Ovention Hotline at 855-298-6836.
CAUTION
Do not move or relocate unit for cleaning. Unit is bulky and
heavy.
Never use steel pads, wire brushes, or scrapers to clean unit.
Wear protective rubber gloves and protective eyewear
when cleaning unit.
Improper cleaning of oven could damage catalyst and will
void unit warranty.
IMPORTANT NOTE:
Use of cleaning chemicals not approved by Ovention when
cleaning the oven chamber will void the warranty.

Daily Cleaning

To maintain performance and preserve the finish of the
Ovention matchbox Oven, clean the unit daily.
CAUTION
Do not turn off Main Disconnect switch or unplug unit
immediately after use. Internal fans must cool oven to
avoid damage to electrical components.
Disconnect switch before
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring
its appearance and making it susceptible to soil
accumulation.
1. Turn off the Standby switch and allow unit to cool. Cooling
fans will operate until the oven chamber temperature drops
below 140°F (60°C).
2. after the cooling fans shut off, disconnect the unit from the
power supply:
• For model m1313, unplug the power cord.
• For model m1718, move the main Disconnect switch to
the OFF (O) position.
3. Remove and discard any remaining food product.
4. Remove and clean each cooking rack using a damp non-
abrasive cloth or nylon scouring pad (a non-abrasive
cleaner may be used for difficult stains).
5. Remove any spillages using damp paper towel or a non-
abrasive cloth.
6. Remove and clean each crumb tray.
• Brush crumbs into a waste container.
• Clean the tray using damp paper towel.
7. Reinstall the crumb trays (see OPERaTION section for
details).
8. Wipe down all exterior surfaces using a non-abrasive,
damp cloth (a non-abrasive cleaner may be used for
difficult stains).
9. Wipe dry all surfaces using a non-abrasive, dry cloth.
10. Polish the exterior surfaces of the oven using a good
quality stainless steel cleaner.

Weekly Cleaning

1. Turn off the Standby switch and allow unit to cool. Cooling
fans will operate until the oven chamber temperature drops
below 140°F (60°C).
2. after the cooling fans shut off, disconnect the unit from the
power supply:
• For model m1313, unplug the power cord.
• For model m1718, move the main Disconnect switch to
the OFF (O) position.
NOTE: To access all sides of the end caps and center divider,
the slider assembly must be moved manually during the
procedure. See the "Cleaning the Slider Assembly"
illustration in this procedure for details.
3. Carefully spray Chemco Dirt Buster III Oven Cleaner onto
all sides of the two end caps and center divider on the
slider assembly (see illustration).
NOTE: Do not spray cleaner directly into the fan opening at the
rear inside of the oven chamber.
4. Using a non–abrasive nylon scouring pad, clean the two end
caps and center divider on the slider assembly. Clean any
other visible area affected by the grease from cooking as well.
14
English
NOTICE
continued...
Form No. OVmm-1013