Technical Data; Before Starting The Equipment; Material Preparation - EINHELL TC-SY 18/60 Li Mode D'emploi

4. Technical data

Motor power supply: ............................18 V
Max fl ow per minute: .............22 fl . oz. (0.65 l/min)
Nozzle size: ............................... 2.0 mm / 2.5 mm
Max viscosity: ....................................... 60 DIN-s
Paint container capacity: ........... 27 fl . oz. (800 ml)
Weight (Paint sprayer alone): ..... 2.65 lbs (1.2 kg)
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's con-struction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.

5. Before starting the equipment

5.1 Spray gun assembly (Fig. 2/3/4)
•
The trigger unit (14) is attached to the drive
unit (15) by a bayonet connector on the gun
mounting (7).
•
Open the locking lever (4).
•
Insert the trigger unit (14) into the gun
mounting (7) with a twist.
•
Close the locking lever.
•
Insert the material tube (11) into the material
tube connection (10)
Anl_TC_SY_18_60_Li_SPK7_USA.indb 12 Anl_TC_SY_18_60_Li_SPK7_USA.indb 12
EN
•
Screw the container into the trigger unit.
5.2 Charging the Lithium-Ion battery (not
included)
The corresponding instructions can be found
in the original operating instructions for your
charger.
5.3 Battery capacity indicator (Fig. 16 / item
20)
Press the battery capacity indicator switch (21).
The battery capacity indicator (20) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
6. Operation
Warning!
Follow the safety precautions provided by the
manufacturer of the material you want to spray.
Use suitable face masks, gloves and protective
clothing.

6.1 Material preparation

The paint usually has to be thinned before it can
be used in the spray gun. Instructions on how to
thin the paint for spraying are not always printed
on the paint tin. You should use the viscosity table
as a guide (viscosity = consistency of the paint).
6.1.1 Measuring the viscosity (Fig. 5)
1. Mix the material thoroughly before measuring.
2. Completely immerse the viscosity cup (8) into
the material.
3. Then lift the viscosity cup (8) out of the mixture
and use a stopwatch to measure the time it
- 12 -
22.04.2022 08:44:25 22.04.2022 08:44:25