Setting-Up And Connecting The Unit; Selecting The Operating Mode; Short Replay Of A Title Beginning; Fast Forward And Reverse Run - Monacor International IMG STAGELINE CD-270DJ Mode D'emploi

vibrations (up to 3 seconds) when replaying.
GB
However, the anti-shock system cannot com-
pensate permanent interruptions.
4 Setting-up
and Connecting the Unit
The control unit and the player mechanism unit
are provided for mounting into a rack for units
with a width of 482 mm (19"), but they can also
be used as tabletop units. The player mecha-
nism unit must always be operated horizontally
whereas the control unit can be installed as
desired, e. g. also inclined. For rack installation
2 rack spaces each are required for the control
unit and the player mechanism unit (1 RS =
1 rack space = 44.45 mm).
Prior to the connection or changing connections,
switch off the CD-270DJ and the units to be con-
nected.
1) Make the connection between control unit
and player mechanism unit: Connect the two
8-pole mini DIN jacks (21 and 24) on the rear
sides of the units via the supplied mini DIN
cable.
2) Connect the stereo outputs LINE OUT for
player 1 (25) and player 2 (22) via RCA cables
to the CD player inputs at the mixer or ampli-
fier.
3) Finally connect the plug of the mains cable
(23) to a socket (230 V~ / 50 Hz).
5 Operation
The operation of player 1 and player 2 is identi-
cal.
5.1 Inserting and replaying a CD
1) Switch on the unit with the POWER switch
(5), the power LED (6) lights up. If no CD has
been inserted into the player mechanism, the
display (11) shows
2) To open the CD tray (3), press the button
(4).
3) Insert a CD with the lettering facing upwards
and press the button or the button
to retract the tray. After reading in the CD, the
display shows (l) = CD in the player
mechanism. The total number of the titles
(indication TOTAL TRACK) is shortly inserted
in the title display field (C) and then the title
number (indication TRACK), the time indica-
tion (E) shortly shows the total playing time
and then the remaining playing time of the
title (switching over the time indication
chapter 5.1.1).
If the tray has been retracted with the but-
ton , the player is set to pause at the first title
after reading in the CD. If the tray has been
retracted with button , the replay of the first
title will start after reading in the CD.
4) To select a title, press the corresponding but-
ton TRACK (17): Each time the button
pressed, one title is advanced; when the but-
ton is pressed, the unit returns to the
beginning of the title first and each time the
button is pressed, one more title is reversed.
5) It is possible to switch between replay [button
lights up, (D) on the display] and pause
[button flashes, (A) on the display] with the
button .
6) After switching-on, always the operating
mode SINGLE PLAY is activated: If a title has
been played to the end, the player is switched
to pause at the beginning of the next title.
8
All manuals and user guides at all-guides.com
However, for continuous replay of the titles
one after the other, switch to CONTINUOUS
PLAY (
(8).
7) To change the CD, first switch to pause, the
CD tray cannot be opened in the replay
mode.
8) Prior to switching off always retract the CD
trays to protect the laser sampling system
against impurities. Then switch off the unit
with the POWER switch.
5.1.1 Switching over the time indication
As a basic setting, the display shows the remain-
ing playing time of the title:
– as a numerical indication (E) in minutes, sec-
onds and frames (1 frame =
– as a bar graph indication (K);
the last 30 seconds of a title are displayed by
the bar graph flashing in its full length, the last
15 seconds by flashing even faster.
With the button TIME (9) the time indication can
be switched over, the respective insertion (F)
shows which time information is presently
shown:
REMAIN inserted:
remaining time of the title
REMAIN disappeared:
replayed time of the title
REMAIN TOTAL inserted:
remaining time of the CD

5.2 Selecting the operating mode

Use the button CONT (8) to switch between the
modes SINGLE PLAY and CONTINUOUS
PLAY. The active mode is shown by the corre-
sponding insertion (H).
A In the mode SINGLE PLAY (replay of indi-
vidual titles) the player is switched to pause
each time a title is replayed.
This mode is especially provided for DJ
.
applications. After reading in the CD or after
selecting a title with the buttons
the player is precisely at the spot where
the music starts (mostly not at the time
index 0 : 00 : 00 but some frames later,
(15)
e. g. 0 : 00 : 15). This spot is automatically
memorized as the starting point (Auto Cue
point). After starting the title, it is possible to
return to this starting point with the button
CUE (14). After replaying a title, the player is
switched to pause precisely at the spot where
the music of the next title starts. This spot is
then memorized as the new starting point.
B In the mode CONTINUOUS PLAY (replay of
all titles) all titles are replayed successively.
At the end of the CD the player mechanism
stops, the display shows the total number of
the titles (C) and the total playing time of the
CD (E).
After reading in the CD and after a title
selection, also in this mode the beginning of
a title is memorized as the Auto Cue point,
is
however, not precisely at the spot where the
music starts but at the time index 0 : 00 : 00.
However, if the titles are not selected via the
buttons
Auto Cue points will be memorized.
5.2.1 Sleep mode
If a player is in the pause mode for more than
30 minutes, it is switched to the sleep mode to
save the laser sampling system. The display
shows
extinguished. Press any button to deactivate the
sleep mode.
chapter 5.2) with the button CONT
1
second)
⁄
75
/ (17),
/ but replayed successively, no
and all illuminated buttons will be

5.3 Short replay of a title beginning

1) If the mode CONTINUOUS PLAY is acti-
vated, set the unit to pause with the button
(15). In the mode SINGLE PLAY the
player can be switched to replay or pause.
2) Select the desired title with the button
(17). After the title selection the player is set
to pause at the beginning of the title (Auto
Cue point chapter 5.2).
3) Keep button CUE (14) pressed. The title is
replayed as long as the button is kept
pressed.
4) After releasing the button, the player returns
to the beginning of the title and is set to
pause. To start the title, press the button
To return to the beginning of the title again,
press button CUE.

5.4 Fast forward and reverse run

1) To switch on the function "fast forward / reverse",
press button SEARCH (7), the display shows
SEARCH (J).
2) Turn the jog wheel (12):
clockwise = forward run,
display
counter-clockwise = reverse run,
display
The speed of the forward run or reverse run
depends on the turning speed of the wheel.
In the mode CONTINUOUS PLAY, the for-
ward run or reverse run also goes beyond
several titles to the beginning or end of the
CD. In the mode SINGLE PLAY the forward
run is possible beyond several titles (then the
player is set to the pause mode), the reverse
run, however, stops when reaching the
beginning of a title.
3) To switch off the function "fast forward / reverse",
press the button SEARCH. The insertion
SEARCH will be extinguished.
The function is also automatically switched
off when the wheel is not turned for 8 seconds.
Notes: In the pause mode, after a forward/reverse, the
present spot is continuously repeated. To stop the
repeat, shortly press the button CUE (14) twice (Cue
point is set chapter 5.6) or start the replay with the
button (15).

5.5 Precise selection of a spot

With the jog wheel (12) a spot on the CD can be
1
located precisely to 1 frame ( second) e. g. for
⁄
75
starting the replay from a certain spot and not at
the beginning of a title.
1) If the desired spot is reached when replaying,
set the unit to pause with the button
2) Prior to turning the wheel the function "fast
forward / reverse" must be switched off: if
SEARCH (J) is shown, press the button
SEARCH (7).
3) By turning the wheel clockwise and counter-
clockwise, precisely locate the spot. The
selected spot is continuously repeated.
4) After locating the spot, shortly press the but-
ton CUE (14) twice. Thus, the spot is memo-
rized ( chapter 5.6) und the repeated
replay stops. With the button
can now be started from this point.
5.6 Return to a spot (Cue point)
defined before
To be able to go quickly to a certain spot, a start-
ing point (Cue point) can be memorized with the
button CUE (14).
1) When replaying, set the unit to pause with the
button (15) when the spot is reached to
return to later. The button CUE (14) flashes.
or
.
on the
on the
(15).
the replay