Using The Remote Control - Jensen AQTIVE II Mode D'emploi Et De Montage

1
2
6
ASSEMBLING/STARTING TO OPERATE THE BED
Check that all the parts have been supplied by referring to the list on page 2
of the brochure.
1. Place the bed bottom up.
2. Unscrew the four transport locks (4 screws) (Figure 1).
3. Fit the legs to the corner attachments on the lower frame (Figure 2).
4. Connect the supply cable to the motor. Wait to connect the motor to a
socket (Figure 3).
5. Connect the supply cable and power cable to the power adapter.
6. Place the bed on its legs.
7. If you have a Seamless cover, put this on now. Refer to the separate
assembly instructions for this.
8. Attach the sidebars using two screws roughly 80 cm from the head end.
Screw into the inside of the lower frame (Figure 4).
9. Attach the footboard using the four bolts already fitted at the foot end of
the bed (Figure 5).
10. Place the mattress and mattress topper on the bed. Pull the cover over the
sidebar (Figure 8).
SETTING THE REMOTE CONTROL FOR THE BED
1. Insert the plug into the wall socket. The motor will now go into pairing
mode and the light under the motor will begin to flash.
2. Press the "head +" and "feet +" buttons down simultaneously for about
three seconds until a short, steady light appears under the motor. The
motor and remote control are now paired.
ELECTRICAL DATA
Power supply: 230 V AC 50/60 Hz.
Standby power: Max. 0.1 W.
MEMORY
1. Put the bed into the position that you want to store in the memory.
2. Hold down the memory button, "M", for at least three seconds. Your
favourite position is now stored in the memory.
3. If you quickly press "=", the bed moves into a flat position.
4. If you press the Memory button again, the bed moves into your stored
position.
UNDER-BED LIGHT
Press the "light bulb" icon to turn the light off or on.
SIMULTANEOUS OPERATION OF TWO BEDS
If you want to operate two beds simultaneously, you can buy a pairing cable
separately or download the smartphone app.
BATTERY IN REMOTE CONTROL IS FLAT
Undo the screw keeping the battery compartment closed. Replace the battery
(CR 2032). Use a PH0 screwdriver and close the cover again.
TROUBLESHOOTING
If you cannot adjust the bed, do the following:
• Check that the plug has been properly inserted into the mains sockets
(wall, power adapter and motor).
• Check the battery in the remote control and replace it, if necessary.
JENSEN AQTIVE II
INTRODUCTION
3
Congratulations on choosing a Jensen Aqtive II adjustable bed. We hope that
it will provide you with good sleep and rest for many years to come. Please
read the instructions carefully before you assemble/install the bed.
4
WARRANTY
5
Jensen Aqtive II beds have a five-year warranty covering normal use. A receipt
showing the date of purchase serves as your warranty certificate. If there are
7
any faults or operational problems, please contact the store where you purcha-
sed the bed. Please mention the motor's item no. and date (see Figure 6).

USING THE REMOTE CONTROL

3You use the remote control to control the bed's movements.
List of remote control functions:
1. Head up
2. Head down
3. Foot up
4. Foot down
5. Under-bed light
6. Flat position
7. Memory
• Remove the plug from the wall, if necessary, wait for 10 minutes and then
insert it in again.
• Reset the remote control; see the separate section.
• Check whether the motor is working with APP.
• Do not open the motor or electrical components yourself. The
manufacturer waives all liability if these actions are carried out by
an unauthorised person. New components should be supplied by an
authorised supplier.
NOISE
An adjustable bed is not silent. The noise coming from the bed may be
amplified by the acoustics of the room it is in.
POWER FAILURE
If the bed is in a raised position when the power failure occurs: Disconnect
the plug from the wall. Loosen the Allen key from the motor. Wind down the
head end and foot end separately. (See Figure 6)
USING THE BED
The bed's lifting motors are not intended for continual operation. Reliable
operation and a normal service life can be achieved when the motors do not
run for more than two minutes during a period of 18 minutes. Exceeding this
limit will shorten the product's service life.
The bed is designed to be able to support a person weighing up to 150 kg,
naturally distributed across the entire bed from head end to foot end. It is
important that you do not sit on the bed's head end or foot end while the bed
is in a raised position or being moved.
Exceeding these limits will damage the product and void the warranty.
NB:
This bed contains moving parts that can trap or injure if not used
with due care. The remote control must be kept out of reach of
children!
JENSEN ADJUSTABLE SLEEP APP
www.jensen-beds.com/assembly-usage
With our app for adjustable beds
you can easily find and store your
favourite position.
Adjust the bed position by
using voice control.
UK
D
F
NL
ESP
N
S
FIN
DK
PL
ITA
PT
4