Electronic Control Setup Instructions; General User Information - Maytag MDE18PD Instructions D'installation

ELECTRONIC CONTROL SETUP INSTRUCTIONS

IMPORTANT
Electrostatic Discharge (ESD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
■ Use an anti-static wrist strap. Connect wrist strap to green
ground connection point or unpainted metal in the appliance.
Touch your finger repeatedly to a green ground connection point
or unpainted metal in the appliance.
■ Before removing the part from its package, touch the
anti-static bag to a green ground connection point or
unpainted metal in the appliance.
■ Avoid touching electronic parts or terminal contacts;
handle electronic control assembly by edges only.
■ When repackaging failed electronic control assembly
in anti-static bag, observe above instructions.

General User Information

BLANK DISPLAY – This condition indicates the dryer is inoperative.
Enter set-up mode to view diagnostic code.
"0 MINUTES" SHOWING IN DISPLAY – This indicates the cycle
is complete and the dryer cannot be operated. Coins dropped
or debit inputs during this condition will be stored in escrow but
cannot be used until normal operation is restored by opening and
closing the door. If a door switch has failed, it must be replaced
before normal operation can be restored.
COLD START (Initial first use) – Dryer is programmed at the
factory as follows:
5 minutes dry time/quarter (coin 1)
$1.50 dry price (fixed cycle with top off)
WARM START (after power failure) – A few seconds after power
is restored, if a cycle was in progress at the time of the power
failure, "RESELECT CYCLE" will flash in the display, indicating a
button needs to be pressed to restart dryer.
PRICING – After the door is opened and then closed following the
completion of a cycle, the display indicates the cycle price (unless
set for free operation). As coins are dropped or debit inputs arrive,
the display will change to lead the user through the initiation of a
cycle.
There are four (4) types of dryer pricing:
Fixed "Vend" Pricing
A dryer set up for "Fixed Cycle" operation can only accept
additional time accumulated by increments equal to the length of a
complete dry cycle. A maximum of 99 minutes may be purchased;
no additional credit is given for coins dropped with 99 minutes in
the display.
22
All manuals and user guides at all-guides.com
-OR-
Accumulator Pricing
If the price is set to one coin 1, then accumulator pricing
is in effect. Cycle time can be purchased one coin at a time up
to the maximum time of 99 minutes. Stacked models will credit
all money to a cycle with a single button press while in accumulator
pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer "Top Off" capability will allow time to be
added to an existing dry cycle in increments equal to the number
of minutes of dry time per quarter (coin 1), up to 99 minutes,
regardless of the cost required to start the dryer. No credit is given
for coins or debit inputs entered when the control is displaying 99
minutes.
FREE CYCLES – This is established by setting the cycle price
to zero. When this happens, "SELECT CYCLE" will appear
rather than a cycle price. Any cycle started as a free cycle will
automatically terminate when the door is opened.
DEBIT CARD READY – This dryer is debit card ready. It will
accept a variety of debit card systems, but does NOT come with a
debit card reader. Refer to the debit card reader manufacturer for
proper dryer setup. In models converted to a Generation 1 debit
card system, debit pulses represent the equivalent of one coin
(coin 1).
Display
After the dryer has been installed and plugged in, the display will
show "0 minutes."
Single Load Models
Once the unit has been plugged in and the dryer door opened and
closed, the display will show the price.
Single Load Models
0
MINUTES
PRICE
1.50