Aux In Operation - Trevi HCV 1035 BT Mode D'emploi

ENGLISH
• Some source devices are unable to display lists of detected devices. To pair this unit with the source device, refer to the source
device operating manual for details.
5. Select "XXXX" from the source list. If Passcode* is required, enter "0000". * Passcode may be called PIN Code, Passkey, PIN
number or Password.
6. Pairing indicator will stop blinking once the unit is successfully paired with the source device.(Pairing information is now
memorized in the unit.) Some audio source devices may connect with the unit automatically after pairing is completed, otherwise
follow the instructions in the source device operating manual to start connection.
7. Press the play button on main unit source device to start Bluetooth connection.
Listening to the sound
Check that:
• The source device Bluetooth functionality is ON.
• Pairing of this unit and the source device is completed.
• Unit is in connected mode (pairing indicator (BT Link) of LCD.)
1. Press the STAND-BY/ON button to turn the power on.
2. Press the MODE button to select Bluetooth function.
3. Start the Bluetooth connection from the Bluetooth stereo audio source device.
4. Press play button (on main unit, remote control or source device).
NOTE:
If the source device has an extra bass function or equalizer function, set them to off. If these functions are on, sound may be distorted.
1. Use a connection lead to connect the portable audio player etc. to the AUDIO IN socket. When using video equipment, connect
the audio output to this unit and the video output to a television.
2. Press the STAND-BY/ON button to turn the power on.
3. Press the MODE button on the remote control or BT/AUX button repeatedly on main unit to select AUDIO IN function.
4. Play the connected equipment. If volume level of the connected device is too high, sound distortion may occur. Should this
happen, lower the volume of the connected device. If volume level is too low, increase the volume of the connected device.
NOTE: To prevent noise interference, place the unit away from the television
In this example, the clock is set for the 24-hour (0:00) display.
1. Press the STAND-BY/ON button to turn the power off.
2. Press the CLOCK button 2 seconds.
3. Press the or button to select 24-hour or 12-hour display and then press the CLOCK button.
: 9
The 24-hour display will appear.(0:00 - 23:59)
The 12-hour display will appear.(AM 12:00 - PM 11:59)
The 12-hour display will appear.(AM 0:00 - PM 11:59)
4. To adjust the hour, press the":"or"9"button and then press the CLOCK button. Press the
time by 1 hour. Hold it down to advance continuously.
5. To adjust the minutes, press the
the time by 1 minute. Hold it down to advance.
NOTE:
When power supply is restored after unit is plugged in again or after a power failure, time display will be blinking. Reset the clock.
To readjust the clock:
Perform " Setting the clock Time" from step.
Timer operation (Remote control only)
Timer playback:
In this example, the clock is set for the 24-hour (0:00) display.
1. Press the TIMER Button once to turn the TIME function on. The TIME indicator " " will appear in the DISPLAY.
2. Press the TIMER button 2 seconds, the display will show "ON" The display will show" "to indicate timer function on and the
"hour" digit of the timer clock will flash.
3. Press the or button to adjust the hours for timer on and then press the Time button.
: 9
4. Press the or button to adjust the minutes ours for timer on and then press the time button.
: 9
20

AUX IN OPERATION

SETTING THE CLOCK TIME (REMOTE CONTROL ONLY)
or button and then press the CLOCK button. Press the
: 9
HCV 1035 BT
or button once to advance the
: 9
or button once to advance
: 9