Operating Instructions; Storage After Use; Maintenance; Troubleshooting - Jetboil MICROMO Mode D'emploi

OPERATING INSTRUCTIONS

WARNING
• Keep burner at arm's length, away from face, during ignition. Flame can flare
during ignition.
• Do not attempt to light with included pot or any other cookware on the burner.
Gas build-up can occur, resulting in increased flame eruption.
• Never expose stove to flammable vapors or liquids while lighting the burner. It
can cause an explosion or fire.
• Do not heat empty pot. Product will melt and potentially catch fire.
• Do not move, lift, or tilt stove with lit burner. Product damage or injury can occur
due to flaring.
• Do not fill pot more than half full. This may cause boil-over, resulting in injury.
• If attempting to heat anything other than water, use care and stir frequently to
avoid boil over or scorching, which may result in product damage or injury.
• Always check that the burner is extinguished before disconnecting the fuel canister.
• Do not use for boiling oil or deep frying. Product damage or injury can occur due
to overheating.
Preparation:
1. Remove bottom cover (7.1) from bottom of the Jetboil pot (7.1). 2. Remove Pack Bag
(if included). 3. Remove Pot Support Warning Tag. 4. Add contents to the pot, cover
with lid, but do not put the pot on the stove yet. Now you are ready to light the burner.
5. Test igniter by depressing igniter button (8.2) until click is heard. If it does not spark,
refer to Maintenance and Troubleshooting sections.
Performance may be suboptimal if used in extreme conditions (cold, hot, wind, altitude).
NOTICE
Do not use stove to warm fuel canister. Can result in explosion.
WARNING
Lighting the Burner:
Ensure burner base is free of any pot prior to lighting. Gas build-up can
CAUTION
occur, resulting in increased flame eruption.
1. Open control valve (8.1) counterclockwise until fully opened and gas flow can be
heard. 2. To light, depress Igniter Button (8.2) until click is heard. Repeat as necessary
until ignition (Fig 9). 3. If ignition does not occur within 5 seconds, close control valves
and wait 5 minutes before repeating the procedure.
Usage:
1. If necessary, rotate control valve (8.1) clockwise to decrease flame setting.
2. Once the burner is lit, carefully place the pot with its contents on the burner base
(Fig 10); turn as shown in Fig 11 to lock into place.
Use care when removing lid. Steam and/or contents may be hot and
CAUTION
7
can cause injury.
After Use:
1. Turn off control valve (8.1) (tighten clockwise) to extinguish flame. 2. Remove pot
from burner base – hold pot by cozy (10.1), and base by shroud (10.2).
Exposed metal parts will be hot and may cause injury if touched.
WARNING
3. Always disconnect fuel canister after use. Unscrew fuel canister from burner base
(Fig 4), and replace plastic fuel cap.
Always check that the burner is extinguished before disconnecting the fuel
WARNING
canister. Vapors can ignite and cause serious injury.
Packing:
1. Allow stove to fully cool before packing. 2. Place bottom cover (7.1) on pot (7.2).
3. Remove stabilizer from canister and fold for storage (1.2). 4. Fold Valve bail under
valve body (1.3). 5. If using the pot support: Remove pot support from burner base (Fig
12), and fold legs (1.4). 6. Refer to Fig 1 for packing contents into pot.

Storage After Use:

1. Always disconnect fuel canister before storing the stove. 2. Ensure stove and pot
are clean and dry before storing. 3. Store the stove in a cool, dry location, indoors.

Maintenance:

1. Flame Check (Every use): The height of the flame should increase from low to
high with counter-clockwise rotation of the control valve. Flame should be blue with
no yellow tipping at full output. Flame should not flash back into burner or lift off of
burner top. If flame abnormalities are found, see your dealer or contact Jetboil for
service. 2. Cleaning Pot (before storage, or as needed): Allow pot to cool before
cleaning. Do not use a dishwasher or abrasive compounds (sand, salt, etc.) to clean.
Only wash by hand with soapy water.

Troubleshooting:

1. Flame does not extinguish: Tighten valve as much as possible, blow out flame,
and immediately detach fuel source. See your dealer or contact Jetboil for service.
2. Igniter fails to spark: If igniter will not spark, check positioning of electrode in
relation to burner. Approximately 1/8" (3mm) length of igniter wire should protrude
from the igniter ceramic. Wire should point toward center of burner with a 1/8" (3mm)
gap between the end of the wire and the top surface of the burner. If not positioned as
described, re-position the electrode accordingly. Bend wire towards center of burner
head and position as described above. If stove is wet, igniter may fail to spark. If igniter
fails to spark, use matches or a lighter, following instructions detailed in OPERATING
INSTRUCTIONS – Lighting the Burners. See your dealer or contact Jetboil for
service if igniter fails to spark for any other reason. 3. If an issue cannot be
corrected using these instructions, see Limited Warranty on back page.
8