Black & Decker FSMH1321 Mode D'emploi page 13

During use, press the steam burst pedal to apply extra
u
cleaning power.
To revert back to normal setting press the pedal again.
u
Hints for optimum use
General
Caution: Never use the steam mop without first attaching a
cleaning pad.
Always vacuum or sweep the floor before using the steam
u
mop.
The easiest way to use the appliance is to tilt the handle
u
to a 45º angle and clean slowly, covering a small area at a
time.
Use water only with no additives or chemicals with your
u
steam mop. To remove stubborn stains from vinyl or
linoleum floors, you can pre-treat with a mild detergent
and some water before using the steam mop.
Steam Cleaning with the mop
Fit hand held steam cleaner (5) to the steam mop body
u
(11)
Place a cleaning pad (13) on the floor with the velcro 'loop'
u
side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(13).
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
dial (2) until the required setting is
Turn the Autoselect TM
u
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
It takes a few seconds for steam to enter the cleaning pad.
u
The steam mop will now glide easily over the surface to be
sanitized/cleaned.
Push and pull the steam mop slowly across the surface to
u
thoroughly steam clean each section.
When you have finished using the steam mop, return
u
the handle (8) to the upright position, making sure that it
is supported and turn it 'OFF'. Wait until the steam mop
cools down (approximately five minutes).
Caution! It is important to monitor the water level in the
water tank. To refill the water tank and continue to sanitize/
clean stand the mop upright making sure that the handle is
supported and turn the steam mop 'OFF'. Unplug the unit from
the electrical wall outlet, and refill the water tank.
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (8) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
(Original instructions)
Carpet refreshing
Place a cleaning pad (13) on the floor with the 'loop' side
u
facing up.
lightly press the steam mop down onto the cleaning pad.
u
Place the carpet glider (12b) on the floor.
u
Lightly press the steam mop down onto the carpet glider
u
until it clicks into place.
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
dial (2) to the Wood/Laminate
TM
Turn the Autoselect
u
setting.
Push and pull the steam mop slowly across the carpet to
u
thoroughly refresh each section.
When you have finished using the steam mop, return the
u
handle (8) to the upright position and turn the unit OFF.
Wait until the steam mop cools down (approximately five
minutes).
After use
dial (2) to the OFF position.
Turn the Autoselect TM
u
Wait until the steam mop cools down.
u
Unplug the steam mop from the electrical wall outlet.
u
Empty the water tank.
u
remove the cleaning pad (13) and wash it ready for next
u
use (take care to follow the wash care instructions printed
on the cleaning pad).
Wrap the supply cable around the cable tidy hooks (7 and
u
9).
There is a hanging bracket (15) built into the hand grip (6)
u
which allows your steam mop to be hung from a suitable
hook on the wall. Always ensure that your wall hook is
capable of supporting the weight of the steam mop safely.
Hand held steam cleaning
Warning! ! Maintain the unit in a horizontal position during
use.
Attach the required accessory.
u
Connect the hand held steam cleaner to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
dial (2) until the required setting is
Turn the Autoselect TM
u
reached. After a few seconds steam will start to come out
of the steam head.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
When you have finished using the hand held steam
u
cleaner turn the Autoselect
Turn the unit OFF by pressing the ON/OFF button (1) and
disconnect from the mains supply. Wait until the unit cools
down before storing (approximately five minutes).
ENGLISH
dial (2) to the OFF position.
TM
13