Bosch GST 18 V-LI S Professional Notice Originale page 1019

20 | English
Technical Data
Angle grinder
Article number
Rated voltage
A)
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding spindle
Weight according to EPTA-Procedure 01:2014
Recommended ambient temperature during charging
Permitted ambient temperature during operation
storage
Recommended rechargeable batteries
Recommended battery chargers
A) Rated speed in accordance with EN 60745-2-3
B) Depends on battery in use
C) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 82
dB(A); sound power level 93 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 6.0 m/s , K = 1.5 m/s ,
h
Disc sanding:
2 2
a = 2.5 m/s , K = 1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
1 609 92A 5WC | (19.08.2020)
V=
-1
min
mm
mm
B)
kg
°C
C)
and during °C
Fitting
Charging the battery
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the Battery
The battery (5) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(6) is pressed unintentionally. As long as the battery is inser-
ted in the power tool, it is held in position by means of a
spring.
To remove the battery (5), press the release button (6) and
pull the battery out of the power tool. Do not use force to
do this.
GWS 18 V-LI GWS 18V-125 V-LI
3 601 J3A 300 3 601 J3A 301
18
11,000 11,000
115
M 14
22
2.0–3.0 2.0–3.0
0 to +35 0 to +35
–20 to +50 –20 to +50
GBA 18V... GBA 18V...
ProCORE18V... ProCORE18V...
GAL 18... GAL 18...
GAX 18... GAX 18...
GAL 36... GAL 36...
Bosch Power Tools
18
125
M 14
22