Télécharger Imprimer la page

Broan QP Serie Manuel D'instructions page 2

Publicité

Les langues disponibles

Les langues disponibles

cLEaning & maintEnancE
For performance, appearance, and health reasons, clean filter,
fan and grease-laden surfaces. Use only a clean cloth and mild
detergent solution on stainless and painted surfaces.
Clean all-metal filters in the dishwasher using a non-phosphate
detergent. Discoloration of the filter may occur if using phosphate
detergents, or as a result of local water conditions - but this will
not affect filter performance. This discoloration is not covered
by the warranty.
The motor is permanently lubricated and never needs oiling. If
the motor bearings make excessive or unusual noise, replace
the motor with the exact service motor. The impeller should also
be replaced.
Use 120 V, 35 W, shielded halogen bulbs - MR16 with GU10
base. Purchase bulbs separately.
oPEration
Always turn the hood ON before cooking in order to establish an
air flow in the kitchen. After turning off the range, let the hood run
for a few minutes to clear the air.
Operate the hood as follows:
0
1
BLowEr SwitcH
This 3-position rocker switch turns blower ON and OFF and
controls blower speed.
Left rocker position (0) turns blower OFF.
Center rocker position (1) turns blower ON to low speed.
Right rocker position (2) turns blower ON to high speed.
LigHt SwitcH
This 3-position rocker switch turns lights ON and OFF and controls
their intensity.
Left rocker position (0) turns lights OFF.
Center rocker position (1) turns lights ON to low intensity.
Right rocker position (2) turns lights ON to high intensity.
2
0
1
models QP130Bl • QP130BlC • QP130ss • QP130ssC
QP130WW • QP130WWC • QP136Bl • QP136ss • QP136WW
PrEParE HooD Location
SOFFIT
CABINET
24" - 30" ABOVE
COOKING SURFACE
1
Determine whether hood will discharge vertically (3¼"
x 10" or 7" Round), or horizontally (3¼" x 10" only). For
vertical or horizontal discharge, run ductwork between
the hood location and a roof cap or wall cap. For best
results, use a minimum number of transitons and
elbows.
2
Use the proper diagram below, for placement of
2
ductwork and electrical cutout in cabinet or wall. For a
non-ducted installation, DO NOT cut a duct access hole.
*
the cabinet front, 4-7/8" to the right of the cabinet
center line.
HOOD MOUNTING SCREWS (5)
WOOD SHIMS
(recessed-bottom
cabinets only)
ROOF CAP
3¼" X 10" or
7" ROUND DUCT
(For vertical
discharge)
HOOD
HOOD
Note the extra wood shim and mounting screw near
5 /
5 /
11
"
11
8
(30" hood)
5 /
5 /
14
"
14
(36" hood)
8
CABINET FRONT
CABINET
BOTTOM
5¼"
5¼"
VERTICAL DUCT
4½"
ACCESS HOLE
¾"
CENTER
LINE
Page 
HOUSE WIRING
(Top or Back of hood)
WALL CAP
3¼" X 10" DUCT
(For horizontal discharge)
3¼" X 10"
VErticaL Ducting
"
(30" hood)
8
"
8
(36" hood)
*
7 /
4
"
8
1 /
8
"
2
7 /
10
8
3 /
2
"
8
5 /
2
"
8
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)
"

Publicité

loading