Bosch EXACT ION 18 V-LI Notice Originale page 16

OBJ_BUCH-1781-004.book Page 16 Thursday, March 16, 2017 9:02 AM
16 | English
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-2.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-2:
Screwdriving without impact: a <2.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
 Before any work on the power tool, remove the battery.
Battery Charging
 Use only the battery chargers recommended by Bosch
for this power tool. Only these battery chargers are
matched to the lithium ion battery used in your machine.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery 9 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 10 unintentionally. As long as the battery is
1 609 92A 3TZ | (16.3.17)
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery 9, press the unlocking button 10
and pull out the battery toward the front. Do not exert any
force.
Battery Charge-control Indication (yellow LED)
Battery Charge-
control Indica-
tion 7
2 2
, K=1.5 m/s .
Flashing light +
audio signal
Continuous light Capacity no longer sufficient for a new
Flashing light
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For proper operation, the allowable ambient temperature
should be between 0 °C und +45 °C at an allowable relative
humidity between 20 and 95 %, free of moisture condensa-
tion.
Suspension Device (see figure B)
With the utility clip 11, the machine can be attached to a sus-
pension device.
– Fasten the utility clip 11 to the machine by engaging it into
the fastening slots 12.
 Regularly check the condition of the utility clip and the
hook of the suspension device.
Configuring the Power Tool
With the BOSCH EXACT Configurator software, different pow-
er tool settings (e. g., speed, driving stages, repeat protec-
tion) can be configured. For this, the power tool must be con-
nected to a PC via the USB data port.
Note: Observe all safety warnings and instructions in the soft-
ware instruction manual.
Changing the Tool (see figure C)
 When working with an application tool, pay attention
that the application tool is firmly seated on the tool
holder. When the application tool is not firmly connected
with the tool holder, it can come loose again and not be
controlled.
Meaning
Battery Charging:
Only 6–8 more screwdriving operations
possible.
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
Bosch Power Tools