Thermotte®/Vermiculite Plates; Door And Glass; Warranty - Nordpeis N-24 Manuel D'installation

Thermotte®/Vermiculite Plates
These insulating plates (FIG 8) in the burn chamber
contribute to a high combustion temperature, which
leads to cleaner combustion of the wood and a higher
rate of efficiency. Any fissures in the plates will not
reduce their insulation efficiency. If new plates are
needed, contact your dealer. Please note: Wood logs
that are too long can cause additional strain and crack
the plates, due to the tension created between the
side plates.
In case it is necessary to take out the insulation
plates, this is done in following order.
1. Lower smoke baffle plate with air chamber*
2. Back plate
3. Left corner plate
4. Right corner plate
5. Right side plate
6. Left side plate
7. Bottom plates
8. Front strip
9. Upper smoke baffle plate** (rabbeted side up)
* When exchanging the lower smoke baffle (part 1), the air
chamber must be removed and fastened on to the new plate.
** When exchanging the upper smoke baffle (part 9) the steel
bracket must be removed and fastened on to the new plate.

Door and Glass

Should there be any soot on the glass it may be
necessary to clean it. Use dedicated glass cleaner.
(NB! Be careful, detergents can damage the varnish).
If different detergents are used they may damage
the glass. A good advice for cleaning the glass is
to use a damp cloth or kitchen roll paper and apply
some soot from the burn chamber. Rub around the
soot on the glass and finish off with a piece of clean
and damp kitchen roll paper. NB! Only clean when
the glass is cold. Check regularly that the transition
between the glass and the door is completely tight.
Possibly tighten the screws that hold the glass in
place - but not too hard, as this can cause the glass to
crack. Periodically, it may be necessary to change the
gaskets on the door to ensure that the burn chamber
is air tight and working optimally. These gaskets can
be bought as a set including ceramic glue.
In order to unhinge the door, do as follows:
Remove the transportation safety device (FIG 9A) that
is fastened in the upper door hinge, in case it is still in
place. Open the door and tighten carefully the little
Allen screw (B) that is on the inside of the door, just
above the lower hinge. Hold the door and carefully
press the top of the door towards the top of the door
frame simultaneously as the lower part is pulled
away from the door frame. Lower the door until the
upper hinge releases from the door frame (FIG 9B).
Remember to loosen the Allen screw again when the
door is put back on. This will release the inner bolt in
the hinge so that this will fall in place.
REFRACTORY
GLASS CANNOT
BE RECYCLED
Refractory glass should
be disposed of as resid-
ual waste, together with
pottery and porcelain
Recycling of the refractory glass
Refractory glass cannot be recycled. Old glass, bre-
akage or otherwise unusable refractory glass, must be
discarded as residual waste. Refractory glass has a
higher melting temperature, and can therefore not be
recycled together with glass. In case it would be mixed
with ordinary glass, it would damage the raw material
and could, in worst case end the recycling of glass.
It is an important contribution to the environment to
ensure that refractory glass does not end up with the
recycling of ordinary glass.

7. Warranty

Read the entire user manual carefully to ensure
proper use and installation of your new Nordpeis
insert. After installation the insert should be
checked.
The steel inserts from Nordpeis AS benefit of a
5-year warranty. The warranty requires the insert to
be installed in accordance with applicable laws and
regulations, as well as the user manual. Notification
of damage and possible consignment of parts for
replacement must be done immediately to the retailer
where the insert was bought. Any claim must be
submitted with a dated invoice or a valid warranty
card.
The warranty does not include consumables such
as: Thermotte® / Vermiculite plates, smoke baffle,
glass and gaskets. Should any of the mentioned parts
break, or need to be changed due to wear and tear,
new parts can be ordered from your retailer. However,
if a material or production error can be documented
on any of the mentioned parts, the warranty is valid for
2 years after the date of purchase.
The warranty does not include damages that are
caused by wrong installation or misuse of the insert,
e.g. incorrect draught regulation or use of incorrect
fuel. The warranty does neither include interference
with operations outside the control of Nordpeis, such
as chimney draught etc. There is no compensation for
third party damage or damage to other items caused
by use of the insert.
The inserts have a plaque with the RRF number 29 09
1920. The CE mark is placed on the heat shield at the
back of the insert.
GB 13