Corsair VIRTUOSO RGB WIRELESS XT Mode D'emploi page 4

GETTING STARTED WITH YOUR CORSAIR VIRTUOSO RGB WIRELESS XT HEADSET
WIRED MODE
Wired mode has two connection options, USB and 3.5mm. To enable wired mode, move the Wireless/Wired
mode operation selector to the "Wired" position. Use the USB connection on PC for the highest quality audio
reproduction (up to 24bit/96kHz audio). The 3.5mm analog connection allows compatibility with most mobile
devices. Use the included 3.5mm inline controller to connect to mobile device or console controllers for optimal
performance and volume and mute control. The "wired" position is also used to turn the headset off when not
charging or connecting wirelessly.
WIRELESS MODE
PC
To enable wireless mode, move the Wireless/Wired mode operation selector to the "Wireless" position.
Connect the wireless USB transmitter to any USB (type-A) port on your PC. The headset is designed to operate
at a range of up to 60 feet (18.2m) from the transmitter, but other wireless devices, electronics and obstructions
such as walls may impact performance. When the headset is set to this mode and not being used, the headset
will automatically go to sleep after 10 minutes to conserve battery life. It will automatically wake up when picked
back up.
IMPORTANT: The first time you use the CORSAIR VIRTUOSO RGB WIRELESS XT Headset transmitter on
a PC, the operating system will automatically install the device driver. After the device driver
loads, we recommend you reboot your PC before use.
iCUE
Go to corsair.com/support/downloads to download the iCUE software.
Using the iCUE software will enable the full feature set of your headset.
Note: if the headset is used without software, some features will be disabled.
> Install the iCUE software on a PC running Windows 10 or later.
> After installation is complete, reboot your PC, and launch iCUE.
iCUE software can be used to:
> Choose your RGB LED color preference.
> Select and customize audio equalizer (EQ) settings.
> Adjust microphone input volume, and microphone sidetone.
The software's built-in documentation explains how to use the headset's features in greater detail.
3
WIRELESS MODE (PLAYSTATION)
Connect the wireless USB transmitter to any USB port on your PS4 or PS5 console.
Use the PlayStation UI to set "Output to Headphones" to "All Audio".
Adjust volume control (Headphones) to maximum level. Then adjust volume with the headset volume control.
The CORSAIR VIRTUOSO RGB WIRELESS XT headset must be fully charged before its first use.
> Connect the USB charging cable to any working USB (type-A) port on your PC and
the opposite end to the USB (type-C) charging port on the headset.
The CORSAIR VIRTUOSO RGB WIRELESS XT headset battery has no "memory effect", so there is no need
to completely discharge it before recharging. Remember that the USB charging cable requires a high power
(USB 2.0 or higher) port.
BATTERY STATUS LED INDICATIONS (ON HEADSET)
LOW
RED
LED will pulse while being charged and turn solid green at full charge. When not being charged, LED will blink
based on power levels shown above.
WIRELESS STATUS LED INDICATIONS (ON WIRELESS USB TRANSMITTER)
> When the transmitter is connected to the headset and operating normally, LED will turn solid white.
> If the transmitter cannot connect to the headset, LED will blink red rapidly.
> If headset is turned on and the transmitter is powered on and LED is still blinking red, please use iCUE software
to re-pair the transmitter to the headset.
Go to corsair.com/support/downloads to download the latest version of the iCUE software.
MICROPHONE CONTROL
> Short key press (0.1-1 seconds) on mic mute button toggles mute on (microphone status LED will turn RED)
and off.
> Long key press (2-4 seconds) on mic mute button toggles sidetone on and off.
NOTE: iCUE software can also be used to control these features.
MEDIUM HIGH
ORANGE GREEN
4
ENGLISH