Publicité
Les langues disponibles
Les langues disponibles
11. SEARCH DIAL: The SEARCH DIAL (8) has two func-
tions. Use the SEARCH DIAL (8) to make fine adjust-
ments in pause mode. Use the SEARCH DIAL (8) to
bend the pitch for precise synchronization in play mode.
12.
SEARCH: The SEARCH (20) buttons are used
to move forward or reverse while in play or pause mode,
SEARCH (20) can also be used to find a CUE POINT.
Hold down either button for ultra fast searching.
13. STOP: The STOP (14) button ends CD play.
14. SINGLE: Pressing the SINGLE (15) activates the
AUTO CUE function. The AUTO CUE function causes the
unit to pause at the beginning of music of the following
track and allows you to start play immediately from the
start of music without any blank space (which exists at the
beginning of every track). Pressing the SINGLE (15) but-
ton a second time activates the CONTINUOUS function
causing the unit to play continuously (after the last track,
the unit will return to the first track of the disc and contin-
ue to play). Pressing the SINGLE (15) button a third time
deactivates the CONTINUOUS function.
15. TIME/OUTRO: The TIME BUTTON (13) switches the
time display between the 4 available choices listed under
DISPLAY (10). This also switches on/off the Outro func-
tion, which only plays the last 30 seconds of each track.
16. PITCH: Pushing the PITCH BUTTON (16) activates the
PITCH CONTROL SLIDE (17). The pitch of the CD will
change according to the position of the PITCH CON-
TROL SLIDE (17).
17.
PITCH BEND BUTTONS: Pushing the PITCH
BEND BUTTONS (18) will automatically raise the pitch
up to +16% or lower the pitch down to -16% from the
existing pitch setting. Releasing the buttons will return the
pitch to the original pitch setting. You can use this function
to match the pitch bend when mixing from one song to
another.
18. PITCH CONTROL SLIDE: Moving the PITCH CON-
TROL SLIDE (17) up or down will lower or raise the pitch
percentage.
OPERATIONS:
1. Press the OPEN/CLOSE (9) button, place a CD in the
DISC TRAY (6) and press the OPEN/CLOSE (9) button
again. The tray will close into the unit.
2. Push the TRACK SKIP(12) buttons to select the track
you want to play.
3. Press the PLAY/PAUSE (21) buttons and the unit will
instantly play.
CUES:
1. To program a cue point (the spot on a CD at which you
want play to start) select a track and push PLAY/PAUSE
(21) so the unit enters the PLAY mode. (PLAY/PAUSE
LED glows green).
2. When the CD reaches the approximate musical spot you
wish to make your cue, push PLAY/PAUSE (21) so the
unit enters the PAUSE mode (PLAY/PAUSE LED blinks
and the unit will enter stutter mode). Move the SEARCH
DIAL (8) forward or in reverse until you reach the precise
frame is located, at which point you will want the CD to
begin play. Push CUE (22). The cue point is now pro-
grammed, the blue LED will remain on. Press and hold
CUE (22) to preview the cue point. Release CUE (22) to
return to the cue point. Press CUE (22) to return to this
pre-programmed cue point to play at any time.
NOTE: ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY
NOT GO BACK TO YOUR PROGRAMMED CUE POINT. YOU MUST
BEGIN YOUR CUE SELECTION OVER AGAIN ONCE YOU HAVE
SKIPPED TO ANOTHER TRACK. THE CUE WILL BE PRESET TO
THE BEGINNING OF THE SELECTED TRACK. PRESS THE CUE
BUTTON AND YOU WILL BEGIN AT THE BEGINNING OF YOUR
SELECTED
TRACK.
SEQUENCE OVER AGAIN.
3. To fine tune your pre-programmed cue point, push the
CUE (22) button and the CD will return to the cue point
you programmed in step #2. Push PLAY/PAUSE (21) so
the unit enters the PAUSE mode at that point. Use the
SEARCH DIAL (8) to move forward or backward to find-
the proper Cue point. Repeat step #2. If you decide this
cue or starting point is okay, leave the unit alone until you
are ready to play.
4. If, however, the selected spot is not exactly where you
want it, push the CUE (22) button while the CD is playing
and the disc will return to the preprogrammed cue point.
Repeat step #1 - #3.
NOTE: DURING FINE TUNING THERE WILL BE A STUTTER EFFECT
(TO HELP YOU FIND THE BEAT). THE STUTTERING EFFECT WILL
END WHEN YOU PRESS THE PLAY/PAUSE (21) TO SAVE THE CUE
POINT.
TROUBLESHOOTING:
· If the disk will not play, check to see if the disc was
loaded correctly (label side up). Also check the disc for
excessive dirt, scratches, etc.
· If the disc turns but there is no sound, check the cable
connections. If they are okay, check your amplifier or
receiver.
· If the CD skips, check the CD for dirt or scratches. Do not
assume that the CD player is defective. Many CDs are
recorded out of spec and will skip on most or all CD play-
ers. Before sending the unit in for repair, try playing a CD
that you are sure plays properly.
SPECIFICATIONS:
GENERAL:
Type......................................................Compact Disc Player
Disc Type................Standard Compact discs (12 cm & 8 cm)
Time Display...Track Elapsed, Track Remain, or Total remain
Variable Pitch....................± 16% Slider with Resume Switch
Pitch Bend...................................................± 16% Maximum
Instant Start............................................Within 0.03 seconds
Track Selection................................................1 to 99 Tracks
Installation................................................................19" each
Dimensions.....................................................19" x 3.5" x 10"
Weight (total)...........................................10.21 lbs. (6.21 Kg)
AUDIO SECTION:
Quantization..................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate....................................................8 Times
Sampling Frequency................................................44.1 kHz
Frequency Response....................................20 Hz to 20 kHz
Digital Output.............................................................IEC958
Total Harmonic Distortion...........................Less Than 0.05%
Signal to Noise Ratio.....................................................85 dB
Dynamic Range............................................................85 dB
Channel Separation......................................................85 dB
Output Level............................................2.0 +/- 0.2V R.M.S.
Power Supply....................................AC 115/230V, 60/50 Hz
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITH-
OUT NOTICE FOR PURPOSE OF IMPROVEMENT.
(5)
START
YOUR
CUE
PROGRAMMING
Publicité
