Publicité
Les langues disponibles
Les langues disponibles
8.6
8.6
Position the ladder in its fully stowed (closed)
Position the ladder in its fully stowed (closed)
position carefully in the loft.
position carefully in the loft.
8.7
8.7
Remove the stud and plastic top tip from the
Remove the stud and plastic top tip from the
top of the required side stile of the rear ladder frame
top of the required side stile of the rear ladder frame
and discard.
and discard.
8.8
8.8
In their place fit Pivot Tip (F4).
In their place fit Pivot Tip (F4).
8.9
8.9
Locate the power arm linkage plates either
Locate the power arm linkage plates either
side of pivot tip (F4)/ladder stile and align all holes.
side of pivot tip (F4)/ladder stile and align all holes.
8.10
8.10
Secure the stile to the linkage plates using bolt
Secure the stile to the linkage plates using bolt
(F5), washers (F6), nut and nut cap (F7 & F8).
(F5), washers (F6), nut and nut cap (F7 & F8).
Ensure bolt (F5) and nut (F7) are tightened sufficiently
Ensure bolt (F5) and nut (F7) are tightened sufficiently
to allow the linkage to freely rotate without any
to allow the linkage to freely rotate without any
looseness.
looseness.
DO NOT over-tighten the nut as this will restrict
DO NOT over-tighten the nut as this will restrict
smooth operation of the ladder system.
smooth operation of the ladder system.
Handrail Assembly
Handrail Assembly
The handrail (G6) can be fitted to either side of the loft
The handrail (G6) can be fitted to either side of the loft
ladder. It is advisable to fit the handle only after fitting
ladder. It is advisable to fit the handle only after fitting
the power pivot arm.
the power pivot arm.
9.1
9.1
Fix the handrail to your chosen side of the
Fix the handrail to your chosen side of the
rear frame.
rear frame.
9.2
9.2
Use 3 x spacers (E1), 60mm bolts (E2),
Use 3 x spacers (E1), 60mm bolts (E2),
washers and nuts (E3 & E4) supplied.
washers and nuts (E3 & E4) supplied.
9.3
9.3
You have a choice of 2 different handrail
You have a choice of 2 different handrail
heights which will be dependent on the amount of
heights which will be dependent on the amount of
"in-loft" handrail you require.
"in-loft" handrail you require.
Check that all fixings for the whole assembly are fully
Check that all fixings for the whole assembly are fully
secure.
secure.
*
*
Position 1 fixes handrail in top position
Position 1 fixes handrail in top position
**
**
Position 2 fixes handrail in low position
Position 2 fixes handrail in low position
Operating the Ladder
Operating the Ladder
10.1
10.1
Locate the plastic stowing hook/key (G3) into
Locate the plastic stowing hook/key (G3) into
one end of the stowing pole (G2) and push firmly to
one end of the stowing pole (G2) and push firmly to
ensure the plastic stowing hook/key (G3) is fully located
ensure the plastic stowing hook/key (G3) is fully located
within the pole. Secure hook/key (G3) with screw (G7).
within the pole. Secure hook/key (G3) with screw (G7).
Push the plastic end plug (G4) into the opposite end of
Push the plastic end plug (G4) into the opposite end of
the stowing pole (G2).
the stowing pole (G2).
10.2
10.2
To open the trapdoor locate the key (G3) into
To open the trapdoor locate the key (G3) into
the slot in the catch operator (A1) and turn the catch
the slot in the catch operator (A1) and turn the catch
anti-clockwise until it reaches the travel stop and then
anti-clockwise until it reaches the travel stop and then
lower the trapdoor.
lower the trapdoor.
F8
F8
F7 F6
F7 F6
F4
F4
E3
E3
E1
E1
E2
E2
G6
G6
E1
E1
E2
E2
G6
G6
1*
1*
1*
1*
2**
2**
E1
E1
E2
E2
E2
E2
F4
F5
F5
F6
F6
E4
E4
2**
2**
1*
1*
2**
2**
E1
E1
A1
A1
G3
G3
09
Publicité
