Stow Controller; Use Without Motor Support; Master Power Switch (Fig. E-A); Controller (Fig. E-1) �������������������������������������������������11 ⚠ Warning - Tunturi Cardio Fit M50 Manuel De L'utilisateur

Stow controller

After you finished your workout it is recommended to stow the
controller again
- Bring the controller back towards the stowage of the equipment,
orientated wired end of the controller first, in a smooth movement.
- Wire will rewind again and will be pulled back into the stowage,
some guidance might be needed.
- Click the controller back in place to ensure it stays in place�
⚠ WARNING
• The controller should fit into the stowage easily without too
much effort. If too much effort is required, check if the curled
telephone wire is stowed correctly and is not preventing the
controller from fitting into the stowage.

Use without motor support

The equipment can be used without danger for internal damages
freely. It require the power main switch being in off mode, means
there is no speed display and no movement support�
The natural resistance of the moving parts inside the machine cannot
be changed nor set to other level

Master power switch (fig. E-A)

The equipment is equipped with a master power switch to shut down
the equipment completely.
To start the equipment:
- Insert the mains plug into the wall socket.
- Set the master power switch to the on position�
To stop the equipment:
- Set the mains power switch to the off position�
- Remove the mains plug from the wall socket.
Controller (fig. E-1)
⚠ CAUTION
• Keep the controller away from direct sunlight.
• Dry the surface of the controller when it is covered with drops of
sweat�
• Do not lean on the controller�
• Only touch the buttons of the controller with the tip of your
finger. Make sure that your nails or sharp objects do not touch
the display�
‼ NOTE
• The console will not switch in standby mode but remains in on
mode�
• Please switch the machine in "Off" mode when not being in use.

Explanation of display items

Scan
- Automatically scan paramter display's for : Speed, Time, Dist. &
Cal�
- Each display will be hold 4 seconds�
- Scan LED will light up, when scan function is active.
Speed
- Shows the speed in setting level 1~12.
- Speed LED will light up, when speed parameter is shown.
Time
- Shows the ran time in workout mode�
- Shows the target time when being in programming mode.
Display parameter units: 00:00 Minutes.:Seconds
- Time LED will light up, when Time parameter is shown.
Dist. (Distance)
- Shows the remaining workout time in countdown mode.
Display parameter units: 0.000 KM.Meters.
- Dist. LED will light up, when Distance parameter is shown.
Cal. (Calories)
- Shows the consumed calories in workout mode�
Display parameter units: 000.0 Calories.
- Cal. LED will light up, when Calorie parameter is shown.
‼ NOTE
• This data is a rough guide for comparison of different exercise
sessions which cannot be used in medical treatment
Buttons
Start/ Stop
- Start the selected workout in stop mode�
- Stop active workout when being in workout mode.
Mode
- Select program mode in idle mode.
- Confirm setting to enter next step in programming mode.
- Switch display modes when being in workout mode.
Time
- Set time for workout ( 1 ~ 15 min. ± 1 minute )
- Press once to increase one minute, press and hold to speed up the
input
‼ NOTE
• In programming mode, the time can only count up with one
minute each button press. When reaching 15 minutes, the
setting will start at 1 minute again to repeat the up counting
cycle again.
Reverse
- Set pedal rotation direction in backwards movement when being in
forward setting.
- Set pedal rotation direction in forward movement when being in
backward setting.
- Pressing "Reverse" button in operational mode will bring the
equipment to a smooth stop, keep stop for about 2 seconds,
before motor can the reverse mode can be activated�
‼ NOTE
• When equipment is in direction reverse mode, all buttons are not
operational, until machine is set into motion again.
Speed +/ Speed -
- Press "Speed +"to increase speed for desired motorize speed
support level mode�
- Press "Speed -" to decrease speed for the desired motorize speed
support level mode�
- Press once to increase/ decrease one level, press and hold to
speed up the input
- Below the table showing each level representing the commencing
RPM ( Rotations per Minute)
Speed
1 2 3
RPM 35 39 43 48 52 56 60 64 68 73 77 80
1 1
GB
4 5 6 7 8 9 10 11 12