Sygonix 1421458 Mode D'emploi page 4

Connecting the smartphone/tablet to the camera
• Open the appropriate WLAN settings on your smartphone or tablet. You will find
the item WLAN in the settings menu on your device.
• Connect your device to the WLAN of the camera. This is "IPCAM_XXXXXX" . The
6 X differ on all cameras. The network is not encrypted; you do not need to enter
a password.
• Once the connection is established, start the previously installed app "Mini WiFi
Cam" .
Setting up the camera in the app
• In the app tap the button with the camera icon "Click here to add camera" to add
a new camera.
• In the next screen display search for the camera. Tap on the magnifying glass.
• Tap on the corresponding camera, once it was found.
The camera is now added to the home page of the app.
• You can now use and control the camera via the integrated WLAN hotspot. Tap
on the camera.
Operating the camera
• You will see now the live image of the camera. Before you continue, you should
first adjust the camera mechanically.
• On this page of the app you can do the following:
With the loudspeaker icon on the far left bottom, you can switch the camera's
microphone on or off.
This camera model does not support the feature of the second symbol.
When you tap the middle icon, you can adjust resolution and refresh rate.
With the second icon from the right (video camera), you can start video record-
ing. To exit, simply tap again on the currently red highlighted icon.
You can take a photo using the right button (photo camera).
• If you switch back to the main menu with the back arrow on the top left, you can
tap on the button "Gallery" (bottom centre) to view the footage.
• Tap on the corresponding camera to view videos and photos. By tapping you can
play back the photos or videos.
• To delete footage, tap the respective gear.
Advanced camera settings
• To change settings, use the button "Camera" (bottom right) to switch back to the
main menu and tap the gear on the right of the camera.
Here you can open the advanced settings by tapping on "Settings".
Here you also synch the time of the camera with your smartphone or tablet
("Adjust"), delete the camera ("Delete") or change the camera name or assign a
password with "Edit" .
You should create a password for the user "admin" anyway, so that access to
the camera is protected.
• Tap on "Settings" to open the advanced settings.
Among other things you are able to set up email forwarding ("Mail Settings"),
change the settings for motion detection ("Motion detection") and alerts ("Alarm
Settings") and create or change users who will have access to the camera ("User
Settings").
Also here you can optionally reset the camera to factory settings ("Restore de-
fault"). However, you can do this also manually on the camera. Refer to the re-
spective chapter (Resetting the Camera to Factory Settings).
The last item "AutoUpgrade System Firmware" lets you upgrade the camera's
firmware. To be able to do this, the camera must be connected to your network
and the Internet.
• Tap on the button "WiFi Settings" to integrate the camera into your existing
WLAN network, so that it can access the Internet and you can access the camera
using your normal network.
• After a quick search your normal WLAN should appear.
Tap on the network and then enter your WLAN password.
• Tap on "Save" to save and apply and then on "Yes" to restart, the camera.
• After the restart, the camera will be registered on your router via WLAN. If this
does not happen automatically, you must reconnect your phone or tablet to the
WLAN of your router.
A connection is successful, when you see the bright blue WLAN icon which will
display in the app on the camera. Once the camera is connected to the Internet,
the yellow LED on the rear is lit permanently.
Resetting the camera to the factory settings
• To reset to the factory settings, connect the camera to the power supply, switch
it on and wait for about 1 minute until the boot process is complete.
• Press the recessed reset button on the device for about 5 seconds until the yellow
network LED on the rear of the camera flashes quickly and is no longer steady or
slowly flashing. Then release the button. The button is located on the right below
the micro SD card slot, next to 3 LEDs.
• The camera will now restart. This takes approx. 1 minute. After that the device is
reset to the factory setting.
Maintenance and Cleaning
• The product does not require any maintenance.
• The outside of the product should be cleaned only with a clean, soft, dry cloth. To
prevent scratches, do not press too hard on the camera front when cleaning.
Do not use abrasive cleaning agents, or other chemical solutions, since these
could damage (discolour) the housing or even impair operation.
Disposal
The product must not be disposed of in household waste!
Dispose of the waste product in accordance with the applicable legal re-
gulations.
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby de-
clare that this product conforms to the fundamental requirements and other rele-
vant regulations of the 1999/5/EC directive.
The Declaration of Conformity (DOC) for this product can be found at
www.conrad.com.
Technical data
a) Product
Operating voltage ......................................... 5 V/DC
Power consumption ..................................... max. 450 mA
Battery ........................................................... rechargeable
Recharging .................................................... via the enclosed power adapter
Battery runtime ............................................. up to 1 hour
Transmission standard ................................. WLAN, 2.4 GHz b/g/n
Range ............................................................. 8 m
Supported memory cards ............................ micro SD, micro SDHC, max. 32 GB
Camera sensor .............................................. 1/4" CMOS
Camera angle ................................................ 75°
Video resolution ............................................ 1280 x 720 Pixel (720p); 25 FPS
Video format ................................................. ASF (M-jpeg; H.264)
Range in darkness ........................................ max. 3 m
Supported operating systems (app)............ AndroidTM from version 2.0 onward;
Dimensions (H x W x D)................................ approx. 63 x 31 x 65 mm (camera and
Dimensions (Ø x T) ........................................ approx. 28 x 65 mm (camera only)
Weight ............................................................ approx. 52 g (incl. wall mount)
Operating conditions .................................... -10 °C to +50 °C; 20% to 85% relative hu-
Storage conditions ....................................... -20 °C to +60 °C; 0% to 90% relative hu-
b) Power adapter
Operating voltage ......................................... 100 - 240 V/AC, 50/60 Hz, max. 0.18 A
Output ............................................................ 5 V/DC, 1 A
Legal notice
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also
in part, is prohibited. This publication represent the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
Lithium-ion battery,
3.7 V/DC, 420 mAh
Apple iOS from version 6 onward
holder)
midity
midity
Nr. 15913C1