stayer GAS CUTTER 33 Instructions D'emploi page 26

- When the machine is placed in storage for a long
time, drain fuel from the fuel tank and carburettor,
clean the parts, move the machine to a safe place
and confirm that the engine is cooled down.
SPECIFIC SAFETY WARNINGS
7.
- BLADE CAN RECOIL VIOLENTLY FROM MATERIAL
IT CANNOT CUT – Blade can cause you to lose arms
or legs. Keep people and animals 30 feet (10 meters)
away in all directions. If blade contacts foreign objects
during operation, turn off engine and allow blade to
come to a halt. Then check blade for damage. Always
discard blade if it is warped or cracked.
- BLADE CATAPULTS OBJECTS THROUGH AIR -
You can be blinded or injured. Wear eye, face, and
leg protection. Always clear work area of any foreign
objects before using blade. Keep people and animals
10 metres away in all directions.
- BLADE COASTS AFTER THROTTLE IS RELEASED
- A coasting blade can injure you or bystanders.
Before servicing the blade, always turn off engine,
and be sure coasting blade has stopped.
- WARNING DO NOT USE ANY OTHER FUEL than
that recommended in your manual. Always follow
instructions in the Fuel and Lubrication section of this
manual. Never use petrol unless it is properly mixed
with 2-cycle engine lubricant. Permanent damage to
engine will result, voiding manufacturer's warranty.
- DO NOT USE ANY OTHER CUTTING ATTACHMENT.
Only use our replacement parts and accessories,
which are designed specifically to enhance the
performance and maximize the safe operation of
our products. Failure to do so may cause poor
performance and possible injury. Use only the
stringhead supplied with this product. Do not use any
other cutting attachment. Use of such attachments will
void your factory warranty and may result in serious
bodily injury.
FUEL AND LUBRICATION
8.
Bike handle installation (Fig. 1)
- Install the U-handle on the fixing holder, install the
clamp and fasten with the screws.
Installation of the toolbar
- Removable bar allows easy transportation. Mount the
connecting rod 16 pressing and rotating until the pin
to penetrate into the hole in the bar. Once the pin A is
within tighten handle B
Installing the protection (Fig. 2)
- Remove the 2 screws on the shield.
- East threaded holes with respect to the bar that is
balanced and floating.
- Adjust the harness straps so that the carabiner is level
Hip.
ENGLISH
26
Installing the harness (Fig. 3)
- Adjust the harness hanger in a comfortable position.
- Buckle the harness at the hanger.
Replace the metal blade to spool
CAUTION: NEVER use unit if blade is warped or
has teeth that are chipped or missing. Replace
a damaged blade immediately.
CAUTION: Always wear heavy-duty work gloves
when handling and installing a blade.
Disassembly metal blade
- Align the hole on the gear box to the slot on the flange
washer
- Use the pin to go through the hole and slot, and hold
the flange washer
- Loose the nut and remove the metal blade and cup
washer
Assembly spool (Fig. 4)
- Install the flange washer and cup washer on the
spindle shaft.
- Install the spool and tighten it.
STOP ENGINE IMMEDIATELY!
Excessive vibration of blade means that it is
not properly installed-stop engine immediately
and check blade. Blade not properly installed will
cause injury.
OPERATION
9.
Fuel
Use regular grade unleaded petrol mixed with 40:1 custom
2-cycle engine oil for best results. Use mixing ratios in
Section FUEL MIXING TABLE below.
WARNING: Never use normal petrol in your
unit. This will cause permanent engine damage
and void the manufacturer's warranty for the
product. Never use a fuel mixture that has been
stored for over 90 days.
WARNING: 2-cycle lubricant must be a premium
grade oil for 2-cycle air cooled engines mixed at
a 40:1 ratio. Do not use any 2-cycle oil product
with a recommended mixing ratio of 100:1. If
insufficient lubrication is the cause of engine
damage, it voids the manufacturer's engine
warranty.
Mixing fuel
Add oil to an approved fuel container followed by the petrol
to allow incoming petrol to mix with oil. Shake container to
ensure thorough mix.
26