Niko 410-004X0 Mode D'emploi page 14

410-004X0
The minimum dimming level is set as follows:
STEP 1 STEP 2
ACTION CONTROL
Lamp on at
minimum level
Lamp still
Dim until
too bright
MINIMUM LEVEL
Is off
MIN MAX
or flickering
OR
If the dimming behaviour at low light intensity is not properly adjusted, try a dimming profile with boost function
(LED 3, LED 7 or LED 8).
3.4. Switching the memory function on or off
Proceed as follows to activate the memory function:
1. Dim up until the maximum light level.
2. Keep the control button pressed for (5) 10 seconds.
3. After 10 seconds the light dims from 100% to a lower light level to indicate that the memory function
has been switched on.
4. Release the control button (5) immediately.
Repeat the procedure to deactivate the memory function.
3.5. Add wireless controls
You can expand the smart dimmer with wireless push buttons according to the Easywave protocol (max. 32).
You can learn a wireless control in three different modes (see table).
The procedure is as follows:
STEP 1: switch the lighting on.
STEP 2: briefly press (< 1.6 s.) the sunk programming button (6) to switch between the different modes
The flashing of the programming LED (1) next to the programming button, indicates which mode you
have chosen:
Mode Position
M1* Upper on / lower off
M2 On/off on 1 button
M3 Scene/preset (see § 3.7)
Normal operation - out of programming
OFF
mode
* In combination with the gateway, M1 must always be used.
STEP 3: one by one, control the transmitters which must partner with the receiver. The confirmation of a
well-received address is indicated by a long lighting time of the programming LED (1) 4 s.
14
EN
STEP 3 STEP 4
CONCLUSION ACTION
Minimum
√
/
dimming
level OK
Minimum
X
dimming
Reduce the minimum
level too
dimming level using
high
the MIN DIM LEVEL
(4) button. Continue
to dim until just before
the lamp begins to
flicker or switches off.
Minimum
X
dimming
level too
Increase the minimum
low
dimming level using
the MIN DIM LEVEL
(4) button. Dim up
until the lamp is softly
lit or stops flickering.
Operation
Light signal during programming
time
Infinite
Infinite
Infinite
Infinite
nv Niko sa Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.eu — www.niko.eu
STEP 4: exit the programming mode by briefly pressing the programming button repeatedly (< 1.6 s.) until
you have exited the programming mode and the programming LED (1) no longer flashes.
STEP 5
CONTROL
3.6. Control an extra wireless dimming receiver
You can expand the smart dimmer with other dimming receivers according to the Easywave protocol.
The procedure is as follows:
STEP 1: place the dimming receiver which you want to connect in programming mode 1 (two button
operation: up on/down off).
STEP 2: press the control button (8) of the smart dimmer to connect it to the receiver.
STEP 3: confirm the programming on the receiver.
Test: switch
lamp off and
3.7. Scene/preset
back on again
When you connect a smart dimmer (or any other compatible receiver) to a wireless switch in mode 3, a button
of the latter will operate as an scene or preset control. This allows you to easily add a scene or all-off function
to your installation.
After you have linked a wireless control to the smart dimmer in mode 3 (see § 3.5), you can save an scene
and recall it afterwards.
Save the scene
STEP 1: set the scene/preset connected receiver(s) l (mode 3 for the smart switches and dimmers) in the
desired scene setting (or switch them all off if you want to keep n all-off function).
STEP 2: press the button for 3 seconds to call up the adjusted scene. Now the scene is saved and linked
to the activated transmitters.
Activate the scene
- Briefly press one of the wireless switches with which you saved the scene, to activate the scene.
3.8. Program the behaviour of the feedback LED (5)
The feedback LED (5) can operate in four different ways:
1. as confirmation LED: the LED lights up when the lighting is on (standard setting)
2. as orientation LED: the LED lights up when the lighting is off
3. LED off: the LED never lights up
4. LED on: the LED always lights up
You can adjust the function of the feedback LED at any time. The procedure is as follows:
STEP 1: switch the lighting on.
STEP 2: for 10 seconds, hold down the programming button (6) of the smart dimmer to proceed to the
next behaviour.
The LED (1) will briefly flash three times to confirm. The behaviour of the feedback LED (5) is now changed.
Repeat these steps until the feedback LED has reached the desired behaviour.
3.9. Delete selectively one or more wireless controls from the memory
STEP 1: switch the lighting off.
STEP 2: hold down (> 1.6 s.) the programming button (6) of the smart dimmer.
The programming LED (1) begins to flash quickly
STEP 3: press the control button of the wireless control you want to delete.
The wireless control is deleted from the memory of the smart dimmer.
The programming LED (1) lights up for 4 seconds as confirmation
If you want to delete multiple controls, press the control button of the wireless control(s) you want to delete
from the memory
STEP 4: exit programming mode by briefly pressing (< 1.6 s.) the programming button (6) of the smart dimmer.
The programming LED (1) stops flashing
PM410-004X0R20363