Télécharger Imprimer la page

Fein MULTIMASTER FMM250 Mode D'emploi page 4

Masquer les pouces Voir aussi pour MULTIMASTER FMM250:

Publicité

Les langues disponibles

Les langues disponibles

3 41 01 091 21 0.book Seite 4 Montag, 29. Juni 2009 8:32 08
en
4
e) Do not overreach. Keep proper footing and
balance at all times. This enables better
control of the power tool in unexpected
situations.
f) Dress properly. Do not wear loose clothing
or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewelry or long hair can be caught
in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, en-
sure these are connected and properly
used. Use of these devices can reduce
dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The cor-
rect power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the
risk of starting the power tool acciden-
tally.
Special safety instructions.
This double-insulated power tool is equipped
with a polarized plug (one contact is wider than
the other). The plug will only fit into the polar-
ized socket outlet in one position. Turn the plug
if it does not fit completely into the socket out-
let. If the plug still does not fit, have a qualified
electrician install a polarized socket outlet. Do
not modify or alter the plug under any circum-
stances. Double-insulated power tools nei-
ther require a three-core power cable nor a
power connection with ground contact.
Operate the power tool only off of power sup-
plies whose voltage and frequency values cor-
respond with the values on the type plate of the
power tool.
d) Store idle power tools out of the reach of
children and do not allow persons unfamil-
iar with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tools operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool
bits etc., in accordance with these instruc-
tions and in the manner intended for the
particular type of power tool, taking into
account the working conditions and the
work to be performed. Use of the power
tool for operations different from those
intended could result in a hazardous situ-
ation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical re-
placement parts. This will ensure that the
safety of the power tool is maintained.
When operating the power tool in a damp envi-
ronment, it must be connected via a ground-
fault circuit interrupter (g.f.c.i.). Using special
rubber protective gloves and footwear
increase your own safety.
Use clamping devices or other suitable means
to secure the workpiece to a firm surface.
Holding the workpiece by hand or pressing it
against your body is not sufficient and can
lead to loss of control.
Before mounting or replacing application tools
or accessories, pull the power plug. This pre-
ventive safety measure rules out the danger of
injuries through accidental starting of the
power tool.

Publicité

loading

Ce manuel est également adapté pour:

Multimaster fmm250q7 229 367 229 37