Important Safety Information - Hatco GLO-RAY GRSS Série Instructions Originales

Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property
WARNING
ELECTRIC SHOCK HAzARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Remote mounted control enclosure must be mounted
on a vertical wall and installed in vertical position.
Mounting control enclosure in horizontal position may
result in collection of liquids and lead to an electric
shock.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning,
adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F).
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAzARD: Locate unit a minimum of 25 mm (1") from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
Make sure food product has been heated to the proper
food-safe temperature before placing on the unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding preheated food product only.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
Form No. GRSSCEM1-0715

IMPORTANT SAFETY INFORMATION

This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
414-671-6350; fax 414-671-3976.
BURN HAzARD: Some exterior surfaces on the unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent unit
or its contents from falling accidentally and strong enough
to support the weight of the unit and contents.
Do not operate built-in models without the trim mounting
ring and the control box mounted properly as described in
the installation instructions.
The National Sanitation Foundation (NSF) requires that
units over 914 mm (36") in width or weighing more than
36 kg (80 lbs.) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point of
use, 102 mm (4") legs are included to allow for proper
cleaning access below unit.
Make sure to clean and sanitize stone surface properly
after deep cleaning the surface using abrasives and before
placing food product on unit.
Unit is designed and recommended for use in or on
metallic countertops. Damage to any countertop material
caused by heat generated from Hatco equipment is not
covered under the Hatco warranty. Verify with the
manufacturer that the material is suitable for prolonged
temperatures up to 200°F (93°C).
Built-in units must not have a setpoint temperature higher
than 93°C (200°F). Temperatures exceeding 93°C (200°F)
will damage unit and void warranty.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing off.
Do not modify wiring or cut thermostat capillary on control
box to increase remote mounting distance. Cutting
thermostat capillary will cause unit to overheat and may
damage unit as well as surrounding countertop.
If weight on shelf exceeds 23 kg (50 lbs.), a deflection up to
4 mm (5/32") is possible. If weight on shelf exceeds 45 kg
(100 lbs.), a deflection of 6 mm (1/4") is possible. Shelf is not
guaranteed if weight on shelf exceeds 68 kg (150 lbs.). All
weight must be distributed evenly across entire shelf.
3
.
WARNING
CAUTION
NOTICE