EINHELL GE-CM 36/48 Li M Instructions D'origine page 24

•
Do not clean the lawn mower with running
water, particularly with high-pressure water.
•
We recommend cleaning the equipment im-
mediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be ag-
gressive to the plastic parts in the equipment.
Ensure that no water can get into the interior
of the equipment.
•
For best results, clean the lawn mower with a
brush or rag.
7.2 Maintenance
•
Worn out or damaged blades, blade mounts,
and bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
•
Ensure that all mounting components (i.e.
screws, bolts, nuts etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the equip-
ment for many years to come, all screwed
parts, as well as the wheels and axles, should
be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high per-
formance, but also enables the equipment to
thoroughly cut your grass with minimal effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If the
blade is completely worn out, it must be im-
mediately replaced or ground sharp again. An
excessively vibrating mower means that the
blade is not properly balanced or has become
deformed from striking an object. In this case,
the blade must be repaired or replaced.
•
There are no other parts inside the equipment
which require maintenance.
7.3 Replacing the blade
For safety reasons, we recommend having the
blade replaced by an authorized professional.
Caution! Pull out the safety plug (12) and remove
the battery packs (15)! Wear work gloves! Only
replace the blade with a genuine Einhell replace-
ment blade, as this will ensure top performance
and safety under all conditions.
Anl_GE_CM_36_48_Li_M-Solo_SPK13.indb 24 Anl_GE_CM_36_48_Li_M-Solo_SPK13.indb 24
GB
Carry out the following steps to change the
blade:
1. Undo the fastening screw (see Fig. 11).
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is ins-
talled in the right direction. The blade's air va-
nes must project into the motor compartment.
The dome mounts must be aligned with the
punch holes in the blade. .
4. Then retighten the fastening screw. The tigh-
tening torque should be approx. 25 Nm.
At the end of the season, perform a general
inspection of the lawn mower and remove any
grass and dirt which may have accumulated.
At the start of each season, ensure that you
check the condition of the blade. If repairs are
necessary, please contact our customer ser-
vice center. Use only genuine spare parts.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com
Spare blade Art. No.: 34.054.56
8. Storage and transport
Storage
Store the equipment and accessories out of
children's reach in a dark and dry place at above
freezing temperature. The ideal storage tempera-
ture is between 5 and 30 °C. Store the machine in
its original packaging.
Transportation
•
Switch the machine off and pull out the safety
plug before transporting it.
•
Fit the shipping protectors, if any.
•
Protect the machine from damage and the
strong vibrations that can occur particularly
when transporting in vehicles.
•
Secure the machine against slipping and
tipping over
- 24 -
10.03.2022 11:41:27 10.03.2022 11:41:27