Bosch AdvancedTrimRouter 18V-8 Notice Originale page 19

To rout with the guide bushing (21), proceed as follows:
– Place the power tool with the guide bushing (21) on the
template.
– Move the power tool with the protruding guide bushing
along the template, applying pressure to the sides.
Edge or profile routing (see figure H)
For edge and profile routing without a parallel guide, the
router bit must be fitted with a pilot pin or a ball bearing.
While it is switched on, guide the power tool towards the
workpiece from the side until the pilot pin or the ball bearing
of the router bit is touching the side of the workpiece edge
that you want to machine.
Guide the power tool along the workpiece edge. Pay atten-
tion that the router is positioned perpendicularly. Too much
pressure can damage the edge of the workpiece.
Routing with a Parallel Guide (see figure I)
For routing with parallel edges, you can install the parallel
guide (22).
Secure the parallel guide (22) on the routing base (2) with
the knurled screw (4).
Set the required stop depth with the wing bolt on the parallel
guide (23).
While it is switched on, guide the power tool along the work-
piece edge with a uniform feed and while applying lateral
pressure to the parallel guide.
Routing with a Pilot (see figure J)
The pilot (24) helps when routing edges with router bits
without a pilot pin or ball bearing.
Fit the pilot to the routing base (2) using the knurled
screw (4).
Guide the power tool along the workpiece edge with a uni-
form feed.
Lateral clearance: To change the amount of material being
removed, you can adjust the lateral clearance between the
workpiece and the guide roller (27) on the pilot (24).
Loosen the wing bolt (25), set the lateral clearance you want
by turning the wing bolt (26), then retighten the wing
bolt (25).
Height: Set the vertical alignment of the pilot according to
the router bit you are using and the thickness of the work-
piece you want to machine.
Loosen the knurled screw (4) on the pilot, slide the pilot into
the required position and retighten the bolt.
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Bosch Power Tools
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The recommended lithium-ion batteries are subject to legis-
lation on the transport of dangerous goods. The user can
transport the batteries by road without further require-
ments.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Dispatch battery packs only when the housing is undam-
aged. Tape or mask off open contacts and pack up the bat-
tery in such a manner that it cannot move around in the
packaging. Please also observe the possibility of more de-
tailed national regulations.
Disposal
Power tools, rechargeable batteries, accessor-
ies and packaging should be sorted for environ-
mental-friendly recycling.
Do not dispose of power tools and batteries/re-
chargeable batteries into household waste!
Only for EU countries:
According to the Directive 2012/19/EU on waste electrical
and electronic equipment and its transposition into national
English | 19
1 609 92A 7UJ | (25.05.2022)