EINHELL GC-CL 18 Li E Instructions D'origine page 15

4. Technical data
Idle speed n ..................................... 12,000 rpm
0
Maximum air speed: ..............................210 km/h
Protection class .................................................III
Sound power level L
WA
Sound pressure level L
Uncertainty K ........................................ 3 dB (A)
Vibration a v .........................................≤ 2.5 m/s
h
Uncertainty K ......................................... 1.5 m/s
Weight .......................................................1.5 kg
Power X-Change lithium-ion batteries
Voltage: .................................................. 18 V DC
Capacity: ................................................... 2.0 Ah
Number of cells: ................................................ 5
Power X-Charger battery charger
Input voltage: .....................200-250 V ~ 50-60 Hz
Output voltage: ....................................... 20 V DC
Output current: ............................................... 3 A
Protection class:............................................II /
Caution!
The equipment and the charger are allowed to
be used only for the lithium-ion batteries of the
Power-X-Change series!
Measured and guaranteed sound power level
determined in accordance with 2000/14/EC,
extended by 2005/88/EC.
The value given for vibration was determined in
accordance with a set of standardized criteria and
can be used to compare diff erent products with
one another. This value is also suitable to be used
for estimating the strain on the user caused by the
vibration beforehand.
Caution!
Depending on how you use the device, the actual
vibration emissions can vary from the values lis-
ted above. Take appropriate measures to protect
yourself against vibration stress. Take the entire
work sequence into consideration including times
at which the device is not working under load or
is switched off . Appropriate measures include
among other things regular care and maintenance
of the device and tool attachments, keeping your
hands warm, taking regular breaks and good
work sequence planning.
Anl_GC_CL_18_Li_E_SPK13.indb 15 Anl_GC_CL_18_Li_E_SPK13.indb 15
......................... 79.5 dB(A)
.................... 68.5 dB(A)
pA
2
2
&
GB
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
•
Wear ear-muffs.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Risk of eye damage if suitable safety goggles
are not worn.
5. Before starting the equipment
5.1 Fitting the blower tube (Fig. 3)
Plug the blower tube (Fig. 1) to the motor unit
(Item 3).
5.2 Fitting the battery (Fig. 4a/4b)
Press the pushlock button (Fig. 4a/Item A) of the
battery as shown in Fig. 4a and push the battery
into the battery mount provided. When the battery
pack is positioned as in Fig. 4b, make sure that
the pushlock button latches in place! To remove
the battery, proceed in reverse order!
5.3 Charging the battery (Fig. 5)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock button.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to blink.
- 15 -
07.06.2022 10:05:41 07.06.2022 10:05:41