TFA 35.1163.01 Mode D'emploi page 12

TFA_No. 35.1163_Anleitung 28.08.2021
Wireless Weather Station
Steady (+-1hPa) Stable weather conditions
Decrease (-1-2 hPa) Weather deterioration
Fast decrease(>-2hPa) Significant weather deterioration
9. Alarm mode
• Press the ALARM button in normal mode to enter the alarm mode. 7:00 (default) or the last adjusted alarm time appear on
the display. Press again the ALARM button. The alarm is activated and the alarm symbol appears on the display. Press
again the ALARM button to deactivate the alarm function. The alarm symbol disappears. The display automatically switches
back to the current time display after 5 seconds.
9.1 Alarm time setting
• Press and hold the ALARM button for three seconds to enter the alarm setting mode.
• The alarm symbol and the hour digit are flashing. Press the UP/MAX/MIN or DOWN/RCC button to adjust the hours.
• Confirm the setting with the ALARM button and set minutes in the same way.
• Press the ALARM button again to return to the current time.
• The alarm is activated and the alarm symbol appears on the display.
9.2 Alarm process
• When the alarm is activated, the alarm starts to ring when the set alarm time is reached. The alarm symbol flashes.
• If the alarm is not stopped manually, the ascending alarm tone automatically turns off after two minutes and the alarm will
be reactivated at the same set time on the following day.
• Press any button to turn off the alarm sound and to activate the snooze function. The snooze symbol flashes.
• The alarm will be interrupted for about 5 minutes.
• Press any button to stop the alarm function.
10. Positioning and mounting of the base station and the transmitter
• When placed outdoors, choose a shady and dry place for the transmitter. Direct sunlight may trigger incorrect measure-
ment and continuous humidity damages the electronic components needlessly.
• Place the base station in any room of the house. Make sure to avoid the vicinity of any source of interference such as com-
puter screens, TV sets or solid metal objects.
22
9:18 Uhr Seite 12
Wireless Weather Station
• Once the desired location is chosen, check whether the transmission from the transmitter to the base station is possible
(transmission range of up to 100m in open areas). Within solid walls, especially ones with metal parts, the transmission
range can be reduced considerably.
• If necessary, choose, another position for the outdoor transmitter and/or receiver.
• If the transmission is successful, you can place or wall mount the base station and the outdoor transmitter with the sus-
pension device.
11. Battery replacement
• As soon as the corresponding battery symbol appears in the display, please change the batteries of the base station or
transmitter.
• Please note: When the batteries are changed, the contact between the outdoor transmitter and the base station must be
restored – so always restart both devices or start a manual transmitter search.
12. Additional outdoor transmitters (optional)
• When having more than one external transmitter (maximum 3), select a different channel for each one with the 1/2/3
switch inside the transmitter's battery compartment. Insert two new AAA 1.5 V batteries, polarity as illustrated. Start the
base station operation or the manual search for the outdoor transmitters.
• For the manual search choose the respective transmitter by pressing the CHANNEL button.
• Press and hold the CHANNEL button for two seconds. The last registered transmitter (channel) will be cancelled and the
transmitter search begins.
• The outdoor temperature with highest and lowest values and the channel number appear on the base station display. If you
have installed more than one outdoor transmitter, press the CHANNEL button on the base station to change between the
channels 1 to 3.
• You can also choose an alternating channel display. Press the CHANNEL button. After the last registered channel (1 to 3) a
circle symbol will appear. To deactivate the function press the CHANNEL button again.
• After a successful installation of the outdoor transmitters close the battery compartments carefully.
13. Troubleshooting
Problem Solution
➜ Ensure the batteries' polarities are correct
No indication on the
➜ Change the batteries
base station/transmitter
➜ No transmitter installed
No transmitter reception
➜ Check the outdoor transmitter's batteries
Display "- -. -"
for channel 1/2/3 (only use batteries/rechargeable batteries with 1.5V voltage!)
➜ Restart the transmitter and the base station according to the manual
23