Cgeneral Safety Rules; C.1 Introduction; C.2 Mechanical Safety Characteristics, Hazards; C.3 Protection Devices Installed On The Machine - Nordcap Zanussi Professional ZXLIG Mode D'emploi

• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless
resulting from defects in materials or workmanship reported
within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages,
failures and inefficiencies caused by and/or resulting from;
– insufficient and/or abnormal capacity of the electrical
systems (current/voltage/frequency, including spikes
and/or outages);
– inadequate or interrupted water supply, steam, air, gas
(including impurities and/or other that does not comply
with the technical requirements for each machine);
– plumbing parts, components or consumable cleaning
products that are not approved by the manufacturer;
– customer's negligence, misuse, abuse and/or non-com-
pliance with the use and care instructions detailed within
the appropriate equipment documentation;
– improper or poor: installation, repair, maintenance
(including tampering, modifications and repairs carried
out by third parties not authorized) and modification of
safety systems;
C GENERAL SAFETY RULES
C.1 Introduction
The machines are provided with electric and/or mechanical
safety devices for protecting workers and the machine itself.
Therefore the user must not remove or tamper with such
devices. The Manufacturer declines any liability for damage
due to tampering or their non-use.
C.2 Mechanical safety characteristics,
hazards
The machine does not have sharp edges or protruding parts.
The guards for the moving and live parts are fixed to the
cabinet with screws, to prevent accidental access.
C.3 Protection devices installed on the
machine
C.3.1 Guards
The guards on the machine are:
• fixed guards (e.g. casings, covers, side panels, etc.), fixed
to the machine and/or frame with screws or quick-release
connectors that can only be removed or opened with tools;
• interlocked movable guards (door) for access inside the
machine;
• machine electrical equipment access doors, made from
hinged panels openable with tools. The door must not be
opened when the machine is connected to the power supply.
C.3.2 Safety devices
The machine has:
• a yellow/red main switch that acts as an emergency switch;
• interlocks on the front panels giving access to inside the
machine;
• emergency switch push buttons and stops must be installed
on the rack handling tables in case the racks exceed their
travel.
IMPORTANT
Several illustrations in the manual represent the
machine, or parts of it, without guards or with
guards removed. This is purely for explanatory
requirements. Never operate the machine without
the guards or with the safety devices deactivated.
– Use of non-original components (e. g.: consumables,
wear and tear, or spare parts);
– environment conditions provoking thermal (e. g. over-
heating/freezing) or chemical (e. g. corrosion/oxidation)
stress;
– foreign objects placed in- or connected to- the product;
– accidents or force majeure;
– transportation and handling, including scratches, dents,
chips, and/or other damage to the finish of the product,
unless such damage results from defects in materials or
workmanship and is reported within one (1) week of
delivery unless otherwise agreed;
• product with original serial numbers that have been
removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by
Electrolux Professional.
Warranty does not include scheduled maintenance activities
(including the parts required for it) or the supply of cleaning
agents unless specifically covered within any local agreement,
subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized
customer care.
C.4 Safety signs to be placed on the
machine or near its area
Prohibition Meaning
do not oil, lubricate, repair and adjust
moving parts
do not remove the safety devices
do not use water to extinguish fires
(placed on electrical parts)
Danger Meaning
danger of crushing hands
caution, hot surface
danger of electrocution (shown on elec-
trical parts with indication of voltage)
C.5 Instructions for use and maintenance
Risks mainly of a mechanical, thermal and electrical nature
exist in the machine. Where possible the risks have been
neutralised:
• directly, by means of adequate design solutions.
• indirectly by using guards, protection and safety devices.
Any anomalous situations are signalled on the control panel
display.
ENGLISH
7