I.4 Continuous Water Softener; Salt Container - Nordcap Zanussi Professional ZXLIG Mode D'emploi

ENGLISH
Wash cycles (cont'd.)
Programme Description
For very dirty dishes.
DISHES
For very dirty dishes,
INTENSIVE
trays or pans.
• To stop the wash cycle, press the start button
• To continue the wash cycle, press start button again. The
cycle starts again from where it was stopped.
IMPORTANT
If during the wash cycle, the operator opens the
door for more than 10 seconds, the dishwasher
deletes the current cycle.
• At the end of the wash, the dishwasher:
– at the end of the cycle acoustic signals sounds;
– the display shows the end of the wash cycle;
8
– the start button is green and blinks.
• Open the door and remove the rack containing the clean
dishes.
WARNING
Pay attention to steam and hot
dishes.
CAUTION
The use of "foaming/nonspecific" deter-
gents or in any case detergents used in
different ways from that prescribed by the
manufacturer, can cause damage to the
dishwasher and compromise the washing
results.
NOTE!
To obtain excellence washing performance, use
detergent, rinse aid and descaling agent sug-
gested by Electrolux Professional. In the Electrolux
Professional web site, open the "Accessories and
Consumables" web page and navigate into the
dishwashing equipment tab to order most suitable
detergents and accessories.
I.4 Continuous water softener
IMPORTANT
Unlike conventional water softeners, this continu-
ous softener does not require machine stops for
regenerating the resins.
By means of special resins, this device removes the calca-
reous substances from the feed water, supplying decalcified
water for washing. For the continuous softener to work
properly the resins must be regenerated periodically, with
frequency depending on the hardness of the water and the
number of wash cycles carried out.
14
Degrees of water hardness
Duration Level
soft
360 seconds
medium
540 seconds
hard
very hard
8
.
Water softener regeneration cycle frequency
Water hardness
°f
5 - 11
12 - 15
16 - 19
20 - 23
24 - 27
28 - 31
32 - 35
36 - 39
40 - 43
44 - 47
48 - 50
1.
I.4.1
The water can only be softened if there is salt in the special
container. The salt container must be filled when the dish-
washer is started the first time and whenever the display
shows that the salt is finished, an audible alarm sounds and
the start button
°fH
0 – 5.5
7 – 14
16 – 26.5
> 27
°d °e
2.8 - 6.2 3.5 - 7.7
6.74 - 8.4 8.4 - 10.5
9 - 10.6 11.2 - 13.3
11.2 - 12.9 14 - 16.1
13.5 - 15.1 16.8 - 19
15.7 - 17.4 19.6 - 21.8
18 - 19.6 22.5 - 24.6
20.2 - 21.9 25.3 - 27.4
22.4 - 24.1 28 - 30.2
24.7 - 26.4 31 - 33
26.96 - 28 33.7 - 35.1
Water softener not necessary.
NOTE!
The factory setting of max. outlet water hardness is
10 °f/ 5.6 °d/ 7 °e. During installation of the
appliance, the installation technician should none-
theless check the correct setting of this value.

Salt container

CAUTION
Only use coarse salt with a purity level of
99.8% NaCl. The use of salt with a lower
purity level can cause clogging of the salt
container filter and malfunctioning of the
water softener.
CAUTION
Do not introduce any other chemical
substances such as detergent, rinse aid
or descaling agent, since these would
inevitably damage the appliance. Such
damage invalidates any warranty and
relieves the manufacturer of all liability.
8
blinks in yellow.
NOTE!
Wash cycles can be started just the same, even if
the display signals no salt; in which case the water
used for washing is not softened.
IMPORTANT
Open the salt container only when the display
shows the message that the salt is finished. Open-
ing the cap when NOT necessary can cause spilling
of the saline solution and compromise correct
machine operation.
°dH °cH
0 – 3 0 – 4
4 – 8 5 – 10
9 – 15 11 – 18.6
> 16 > 19
Nr. of cycles
1
—
36
32
28
24
20
16
12
9
3
1