MTD 700 Mode D'emploi page 16

Single Line Installation
Go To Step 8 for Split-Line™ Installation
6. Take approximately 7.6 meters (25 ft.) of new
trimming line, loop it into two equal lengths. Insert
each end of the line through one of the two holes in
the inner reel (Fig. 14). Pull the line through the inner
reel so that the loop is as small as possible.
7. Wind the lines in tight even layers, onto the reel (Fig.
15). Wind the line in the direction indicated on the
inner reel. Place your index finger between the two
lines to stop the lines from overlapping. Do not
overlap the ends of the line. Proceed to step 11.
Split-Line™ Installation
8. Take approximately 3.65 meters (12 ft.) of new
trimming line. Insert one end of the line through one
of the two holes in the inner reel (Fig. 16). Pull the
line through the inner reel until only about 4 inches is
left out.
9. Insert the end of the line into the open hole in the
inner reel and pull the line tight to make the loop as
small as possible (Fig. 16).
10. Before winding, split the line back about 6 inches.
11. Wind the line in tight even layers in the direction
indicated on the inner reel.
NOTE: Failure to wind the line in the direction indicated
will cause the cutting attachment to operate
incorrectly.
12. Insert the ends of the line into the two holding slots
(Fig. 17).
13. Insert the ends of the line through the eyelets in the
outer spool and place inner reel with spring inside the
outer spool (Fig. 18). Push the inner reel and outer spool
together. While holding the inner reel and outer spool,
grasp the ends and pull firmly to release the line from
the holding slots in the reel.
NOTE: The spring must be assembled on the inner reel
before reassembling the cutting attachment.
14. Hold the inner reel in place and install the Bump Knob
by turning clockwise. Tighten securely.
Installing a Prewound Reel
1. Hold the outer spool with one hand and unscrew the
Bump Knob counterclockwise (Fig. 10). Inspect the
bolt inside the Bump Knob to make sure it moves
freely. Replace the Bump Knob if damaged.
2. Remove the old inner reel from the outer spool (Fig. 11).
3. Remove the spring from the old inner reel (Fig. 11).
4. Use a clean cloth to clean the the inner reel, spring,
shaft, and inner surface of the outer spool.
5. Place the spring in the new inner reel.
NOTE: The spring must be assembled on the inner reel
before reassembling the cutting attachment.
6. Insert the ends of the line through the eyelets in the
outer spool (Fig. 18).
16
MAINTENANCE AND REPAIR INSTRUCTIONS
7. Place the new inner reel inside the outer spool. Push
the inner reel and outer spool together. While holding
the inner reel and outer spool, grasp the ends and pull
firmly to release the line from the holding slots in the
spool.
8. Hold the inner reel in place and install the Bump
Knob by turning clockwise. Tighten securely.
AIR FILTER MAINTENANCE
Removing the Air Filter/Muffler Cover
1. Place the choke lever in the position 2.
NOTE: The choke lever must be in position 2 (Fig. 19) to
remove the air filter/muffler cover.
2. Remove the four (4) screws securing the air
filter/muffler cover (Fig. 19). Use a flat blade or T-20
Torx bit screwdriver.
3. Pull the cover from the engine. Do not force.
Cleaning the Air Filter
Clean and re-oil the air filter every 10 hours of operation.
It is an important item to maintain. Failure to maintain
your air filter properly can result in poor performance or
can cause permanent damage to your engine.
1. Remove the air filter/muffler cover. See Removing
the Air filter/Muffler Cover.
2. Remove the air filter from inside the air filter/muffler
cover (Fig. 20).
3. Wash the filter in detergent and water (Fig. 21). Rinse
the filter thoroughly. Squeeze out excess water.
Allow it to dry completely.
4. Apply enough clean oil to lightly coat the filter (Fig. 22).
5. Squeeze the filter to spread and remove excess oil.
6. Replace the air filter inside the air filter/muffler cover
(Fig. 20).
NOTE: Operating the unit without the air filter and air
filter/muffler cover assembly, will VOID the
warranty.
Reinstalling the Air Filter/Muffler Cover
1. Place the air filter/muffler cover over the back of the
carburetor and muffler.
NOTE: The choke lever must be in position 2 (Fig. 19) to
install the air filter/muffler cover.
2. Insert the four (4) screws into the holes in the air
filter/muffler cover (Fig. 19) and tighten. Use a T-20
Torx bit screwdriver. Do not over tighten. Do not
force.
Check Fuel Mixture
Old and/or improperly mixed fuel is usually the reason
for the unit not running properly. Drain and refill the tank
with fresh, properly mixed fuel prior to making any
adjustments.