Publicité
Les langues disponibles
Les langues disponibles
Assembly
(Continued)
2. Place lock washer on axle bolt. Then
tighten nut securely to threaded part
of axle bolt.
3. Repeat procedure with other side.
Installation
LOCATION
The tank must sit level or slope slightly
towards the drain valve to allow the
tank to drain properly.
It is extremely important to install the
compressor in a clean, well ventilated
area where the surrounding air
temperature will not be more than 100°F.
A minimum clearance of 18 inches
between the compressor and a wall is
required because objects could obstruct
air flow.
compressor air inlet near steam, paint
spray, sandblast areas or any other
source of contamination. This debris
will damage the motor.
ELECTRICAL INSTALLATION
and electrical connections should be
performed by a qualified electrician.
Installation must be in accordance with
local codes and national electrical codes.
Never use an extension cord
with this product. Use
additional air hose instead of
an extension cord to avoid power loss
and permanent motor damage. Use of
an extension cord voids the warranty.
GROUNDING INSTRUCTIONS
1. This product is for use on a nominal
120 volt circuit and has a grounding
plug that looks like the plug
illustrated in Figure 3. Make sure the
product is connected to an outlet
having the same configuration as the
plug. Do not use an adapter with this
product. This product must be
grounded. In the event of an
electrical short circuit, grounding
reduces risk of electrical shock by
providing an escape wire for electric
current. This product is equipped
with a cord having a grounding wire
with an appropriate grounding plug.
Cord must be plugged into an outlet
that is properly installed and
grounded in accordance with all local
codes and ordinances.
Figure 3
Improper use of grounding
plug can result in a possible
risk of electrical shock!
Do not
locate the
grounding adapter with this product!
2. If repair or replacement of cord or
plug is necessary, do not connect
grounding wire to either flat blade
terminal. The wire with insulation
All
having an external surface that is
wiring
green (with or without yellow
stripes) is the grounding wire.
green (or green and yellow) wire to a
live terminal.
STOP!
3. Check with a qualified electrician or
serviceman if grounding instructions
are not completely understood, or if
in doubt as to whether product is
properly grounded. Do not modify
plug provided; if it will not fit outlet,
have proper outlet installed by a
qualified electrician.
WIRING
1. Local electrical wiring codes differ
from area to area. Source wiring,
plug and protector must be rated for
at least the amperage and voltage
indicated on motor nameplate, and
meet all electrical codes for this
minimum.
Grounded
Pin
RESET
TEST
Grounded Outlet
Do not
use a
Never
connect
3
Oilless Compressors
MOISTURE IN COMPRESSED AIR
Moisture in compressed air will
form into droplets as it comes from
an air compressor pump. When
humidity is high or when a
compressor is in continuous use for
an extended period of time, this
moisture will collect in the tank.
When using a paint spray or
sandblast gun, this water will be
carried from the tank through the
hose, and out of the gun as droplets
mixed with the spray material.
IMPORTANT: This condensation
will cause water spots in a paint
job, especially when spraying other
than water based paints. If
sandblasting, it will cause the sand
to cake and clog the gun,
rendering it ineffective. A filter in
the air line (MP3105), located as
near to the gun as possible, will
help eliminate this moisture.
2. Use a slow blow fuse or a circuit
breaker.
Overheating, short circuiting and fire
damage will result from inadequate
wiring, etc.
NOTE: 120 volt, 15 amp units can be
operated on a 120 volt circuit under the
following conditions:
a. No other electrical appliances
or lights are connected to the same
branch circuit.
b. Voltage supply is normal.
c. Circuit is equipped with a 15
amp circuit breaker or a 15
amp slow blow fuse.
3. If these conditions cannot be met or
if nuisance tripping of current
protection device occurs, it may be
necessary to operate compressor
from a 120 volt, 20 amp circuit.
www.chpower.com
Publicité
