Denon DVD-2200 Mode D'emploi page 17

When "AUDIO SETUP" is selected
1
1, 2, 3
1
1
See page 12.
Use the • and ª cursor buttons to select the desired setting,
then press the ENTER button.
AUDIO CHANNEL
Use this to adjust for the connected speaker systems.
SUPER AUDIO CD
Super Audio CDs include separate areas for stereo and multi-
channel signals.
Hybrid discs have a two-layered structure consisting of one
Super Audio CD layer and one CD layer.
The area/layer to be played with priority can be set.
2
DIGITAL OUT
Use this to select the digital output's signal format.
LPCM (44.1 KHz / 48 kHz)
Use this to set the digital audio output when playing DVDs
recorded in linear PCM audio.
BASS ENHANCER (2 CHANNEL)
Set whether or not to output audio signals from the
subwoofer when playing two-channel audio signals.
The BASS ENHANCER settings do not apply to digital
outputs.
Use the • and ª cursor buttons to select the desired setting,
then press the ENTER button.
q When "AUDIO CHANNEL" is selected:
B Use the • and ª cursor buttons to select the item to be
set, then press the ENTER button.
MULTI CHANNEL (Factory default)
Select this for systems in which three or more speakers
3
are connected.
When MULTI CHANNEL is set, the speaker settings
(SPEAKER CONFIGURATION), speaker output level
adjustment (CHANNEL LEVEL) and speaker distances
(DELAY TIME) can be set.
2 CHANNEL
Select this for systems in which only two speakers are
connected.
OPEN /
POWER NTSC / PAL CLOSE
ON OFF
PROG / DIR
1 2 3
CLEAR
4 5 6
SRS.TS
7 8 9
CALL RETURN
0 +10
TOP MENU DISPLAY
T. MENU DISP.
ENTER
PLAY
MENU
STILL /
STOP
PAUSE
SKIP SLOW / SEARCH
ANGLE SUBTITLE AUDIO SEARCH MODE
REPEAT A-B RANDOM MARKER
SETUP DIMMER PIC.ADJ
ZOOM PAGE
ENTER
Remote control unit Remote control unit
AUD I O SE TUP
AUD I O CHANNE L MUL T I CHANNEL
SUPE R AUD I O CD MUL T I
D I G I TAL OUT NORMAL
L PCM (4 4 .1 kHz / 4 8 kH z) OF F
BASS ENHANCER(2 CHANNEL) OF F
E X I T SE TUP
SE L ECT : DEC I S I ON : ENTER BUT TON
ENTER
Remote control unit Remote control unit
AUD I O SE TUP
AUD I O CHANNE L MUL T I CHANNEL
SUPE R AUD I O CD 2 CHANNE L
D I G I TAL OUT
L PCM (4 4 .1 kHz / 4 8 kH z)
BASS ENHANCER(2 CHANNEL)
E X I T SE TUP
SE L ECT : DEC I S I ON : ENTER BUT TON
B When "MULTI CHANNEL" is selected, use the • and ª
cursor buttons to select the item to be set, then press the
ENTER button.
SPEAKER CONFIGURATION
Use this to select the types of the different speakers.
CHANNEL LEVEL
Use this to adjust the output level of the different speakers.
DELAY TIME
Use this to set the distance from the different speakers to
the listening position.
To exit the SPEAKER SETUP mode
Use the ª cursor button to select "AUDIO SETUP" then
press ENTER button.
The SPEAKER CONFIGURATION settings only apply to
analog outputs.
B When "SPEAKER CONFIGURATION" is selected, use the
• and ª cursor buttons to select the speaker to be set then
press the ENTER button.
• The type of speaker used for the front speakers, center
speaker, subwoofer and surround speakers can be set.
Use the • and ª cursor buttons to select the speaker
type, then press the ENTER button.
LARGE: Select this when a large speaker is connected.
SMALL: Select this when a small speaker is connected.
NONE: Select this when no speaker is connected.
YES: Select this when a subwoofer is connected.
NO: Select this when no subwoofer is connected.
B When "FILTER" is selected:
ON (Factory default)
3
Set to "ON" to play sources in the Dolby Digital and PCM
multi-channel modes.
OFF
DTS recommended all-channel full band playback setting.
(Note however that the subwoofer volume increases by 5
dB, by 15 dB when playing Super audio CDs.)
Set this to play DVD audio 6-channel sources recorded in
all-channel full band frequencies.
When "OFF" is set, the speaker size is set to "LARGE" for
all the speakers and the subwoofer setting is set to "YES".
To play this type of disc, read the disc's instructions carefully
and make analog connections.
Press the RETURN button to return to the "SPEAKER
SETUP" menu.
B When "CHANNEL LEVEL" is selected, use the • and ª
cursor buttons to select the speaker to be adjusted, then
use the 0 and 1 cursor buttons to set the level.
SW +10 dB
Depending on the connected amplifier, it may not be
possible to increase the subwoofer level to balance it with
the level of other channels. In this case, the SW +10 dB
function can be used to boost the subwoofer output.
When turned on, the subwoofer output is increased by
+10 dB.
Never play at high signal levels (full scale or near full
scale) when the SW +10 dB mode is turned on. The
signal level could exceed the amplifier's tolerance input
level, resulting in noise that could damage the speakers.
If the sound of the subwoofer is too loud or distorted,
either turn the SW +10 dB mode off or lower the gain.
The SW +10 dB function does not work when "FILTER"
at "SPEAKER CONFIGURATION" is set to "OFF".
ENGLISH
ENTER
Remote control unit Remote control unit
SPEAKER SETUP
SPEAKER CONF I GURAT I ON
CHANNE L L EVE L
DE L AY T I ME
AUD I O SE TUP
SE L ECT : DEC I S I ON : ENTER BUT TON
SPEAKER SETUP
SPEAK ER CONF I GURAT I ON
F RONT SP L ARGE
CENT ER SP SMALL
SUBWOOF ER
SURROUND SP
F I L T ER
SE L ECT : DEC I S I ON : ENTER BUT TON
Remote control unit
SPEAKER SETUP
CHANNE L L EVE L
TEST TONE OF F
F RONT L ch 0 dB
CENT ER 0 dB
F RONT Rch 0 dB
SURROUND R ch 0 dB
SURROUND L ch 0 dB
SUBWOOF ER 0 dB
SW 10dB + OF F
SE L ECT : DEC I S I ON : ENTER BUT TON
17