Altrex RS TOWER 51 Manuel page 29

6.2. RS TOWER 51+/52 (90 / 135 cm rolling tower)
A. Base section
A1: Odd working height
1. Start with two 7 rung frames (part T2.A)
2. Place the wheels (part T2.C) in the frames, apply the brake and
point them outwards [T3.1 - T3.3]
3. Place horizontal braces (part T2.G) under the first rung on the
uprights [T3.4 - T3.5]
4. Place the diagonal braces (part T2.H) (rungs 1-5)
5. Place a (temporary) platform without a hatch (part T2.E) on the 3rd
rung [T3.20 - T3.22]
6. Set the base section with a spirit level
7. Mount the triangle stabilizers (part T2.I) [T3.9 - T3.13]
B. Middle section
1. Place the 7 rung frames (part T2.A) and secure them [T3.6 - T3.8]
2. Place the diagonal braces (part T2.H), starting on the rung where the previous brace ends
3. Place a platform with hatch (part T2.D) on the 3rd rung of the last frame fitted
4. Climb through the hatch and sit on the platform with the legs through the hatch and assemble the 4 horizontal braces (part T2.G)
C: End section
1. Place the 7 rung frames (part T2.A) and secure them [T3.6 - T3.8].
2. Place the Safe-Quick Guardrails® (part T2.F) on the upper rung with the instruction label facing inwards [T3.14 - T3.18].
3. Place a platform with hatch (part T2.D) [T3.19 - T3.22].
a. For a wide 135 cm scaffold, also place a platform without hatch (part T2.E) [T3.20 - T3.22].
4. Enter the platform through the trap door and place the toe board kit (part T2.J) [T3.23 - T3.25].
Facade-free use
If necessary for the work to be carried out, the guardrails/Safe-Quick® Guardrail on the facade side of the working platform may be
repositioned. Only to be used if the distance to the facade is maximum 15 cm. Local legislation and regulations may contain supplementary
measures on top of this guide.
6.3. Assembly RS TOWER 54/55
A. Base section
1. Put the wheels into the folding frame (part K), put the brakes on and put them in an outward direction [T3.1 - T3.3].
2. Unfold the folding frame.
3. Place the horizontal brace (part G) under the first rung on the vertical [T3.4 – T3.6].
4. Adjust the base section using a spirit level.
5. Mount a diagonal brace between the 3rd and the 7th rung.
6. Place the temporary platform (part D) on the third rung (T3.20 - T3.22].
7. After the frames mentioned in B. Middle Section are placed, mount the triangle stabilisers (part I) [T3.10 - T3.13].
For completing the assembly of the RS TOWER 54, follow steps B and C of Annex T4.
For completing the assembly of the RS TOWER 55, follow steps B and C of Annex T5.
A2: Even working height
1. Start with two 7 rung frames (part T2.A)
2. Place the wheels (part T2.C) in the frames, apply the brake and
point them outwards [T3.1 - T3.3]
3. Place horizontal braces (part T2.G) under the first rung on the
uprights [T3.4 - T3.5]
4. Place the diagonal braces (part T2.H) (rungs 1-5)
5. Place a (temporary) platform without a hatch (part T2.E) on the
3rd rung [T3.30 - T3.22]
6. Adjust the base section with a spirit level by turning the spindles
7. Mount the triangle stabilizers (part T2.I) [T3.9 - T3.13]
8. Place the 4 rung frames and secure them [T3.6 - T3.8]
9. Place the diagonal braces, starting on the rung where the
previous brace ends
10. Place a platform with hatch (part T2.D) on the 7th rung
11. Climb through the hatch and sit on the platform with the legs
through the hatch and assemble the 4 horizontal braces
(part T2.G)
29
www.altrex.com
EN