Other Features; Auto Start Function; Turbo Function - Krups EC422 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

 Add 1 KRUPS (x) spoonful of ground coffee per cup. Do not exceed 14 spoons (2.5 ounces). Fig. 10.
 If ground coffee has accidentally been poured into the water tank, please do not run the cycle; instead clean
the water tank. The ground coffee could plug the water circuit.
 Close the lid (b).
 Press the ON OFF button (Fig. 11) to turn on the coffee maker and then press BREW
cycle. When the coffee maker begins the brew cycle, the BREW button will light, and the machine will
beep once. Fig. 12.
 When the brew cycle ends, the coffee maker beeps 3 time, the 'keep warm' cycle automatically begins,
and the screen will display the time remaining before the 'keep warm' cycle ends. The BREW button
flashes slowly.
 After the default keep warm time of 4 hours your coffee maker beeps 3 times and the BREW/control knob
(k) switches off.
 At any time during the brew cycle, you may turn off the coffee maker by pressing the BREW/control knob
(k) or ON OFF button. The light on the BREW/control knob will also go out. It beeps 3 times prior to
turning off.
Even if the brew cycle has ended, there is still hot liquid in the filter. Wait a few minutes for the rest of the
liquid to flow into the carafe before removing the filter.
Note :
- The amount of coffee in the carafe at the end of the cycle is less than the amount of water poured into the
water tank, since the ground coffee and the filter absorb about 10% of it.
- The water tank is equipped with an overflow outlet at the rear of the appliance. If you add too much water,
excess water will leak from this opening.
- Clean the permanent filter in between each use, or use a paper filter.
CAUTION:
- To avoid overflowing, the carafe should be properly placed on the warming plate of the coffee
maker, otherwise the hot water or hot coffee may overflow.
- The coffee maker becomes very hot during the brew cycle. Handle it carefully.

6. OTHER FEATURES

6A – AUTO START FUNCTION (AUTO)
Programming the auto-start settings.
 Your appliance is equipped with two auto-start programs.
 Check whether the clock is set to the right time. If not, follow the instructions in the SETTING THE CLOCK
section.
 Press the AUTO button
 Set the time by pressing the HR button
will be displayed. It will be automatically set after about five seconds. The time is displayed. Fig. 14 and 15.
 To set the second program, push the AUTO button twice, so that the AUTO 2 icon appears on screen.
Fig. 16.
 Set the time by pressing the HR button
will be displayed. It will be automatically set after about five seconds or if the BREW button
The time is displayed. Fig. 17 and 18.
Activate a delayed start-up when the time is already pre-set.
 Select AUTO 1 or AUTO 2 by pressing the AUTO button
 To cancel the AUTO 1 and/or AUTO 2 setting, press the AUTO button
6B – TURBO FUNCTION
 This function enables you to brew your coffee faster by reducing the cycle time.
(z)
 Press the TURBO
 The TURBO button lights up.
 This function will be saved in the memory of your coffee machine for future cycles. You can stop this
function by pressing the
10
(p)
. An AUTO 1 icon displays on screen. Fig. 13.
(r)
to set the hour and the MIN button
(r)
to set the hour and the MIN button
Fig. 19
button.
TURBO (z)
button once more.
(s)
to set the minutes. The time
(s)
to set the minutes. The time
(p)
.
(p)
ONE time.
(k)
to start the
(k)
(k)
is pressed.

Publicité

Table des Matières
loading

Table des Matières