Bosch Professional GCM 18V-305 GDC Notice Originale page 17

Keep cutting tools sharp and clean. Properly main-
u
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in
u
accordance with these instructions, taking into ac-
count the working conditions and the work to be per-
formed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and
u
free from oil and grease. Slippery handles and grasping
surfaces do not allow for safe handling and control of the
tool in unexpected situations.
Battery tool use and care
Recharge only with the charger specified by the manu-
u
facturer. A charger that is suitable for one type of bat-
tery pack may create a risk of fire when used with another
battery pack.
Use power tools only with specifically designated bat-
u
tery packs. Use of any other battery packs may create a
risk of injury and fire.
When battery pack is not in use, keep it away from
u
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
Under abusive conditions, liquid may be ejected from
u
the battery; avoid contact. If contact accidentally oc-
curs, flush with water. If liquid contacts eyes, addi-
tionally seek medical help. Liquid ejected from the bat-
tery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or
u
modified. Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire, explosion or risk
of injury.
Do not expose a battery pack or tool to fire or excess-
u
ive temperature. Exposure to fire or temperature above
130°C may cause explosion.
Follow all charging instructions and do not charge the
u
battery pack or tool outside the temperature range
specified in the instructions. Charging improperly or at
temperatures outside the specified range may damage
the battery and increase the risk of fire.
Service
Have your power tool serviced by a qualified repair
u
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Never service damaged battery packs. Service of bat-
u
tery packs should only be performed by the manufacturer
or authorized service providers.
Safety Warnings for Mitre Saws
Mitre saws are intended to cut wood or wood-like
u
products, they cannot be used with abrasive cut-off
wheels for cutting ferrous material such as bars, rods,
Bosch Power Tools
studs, etc. Abrasive dust causes moving parts such as
the lower guard to jam. Sparks from abrasive cutting will
burn the lower guard, the kerf insert and other plastic
parts.
Use clamps to support the workpiece whenever pos-
u
sible. If supporting the workpiece by hand, you must
always keep your hand at least 100 mm from either
side of the saw blade. Do not use this saw to cut pieces
that are too small to be securely clamped or held by
hand. If your hand is placed too close to the saw blade,
there is an increased risk of injury from blade contact.
The workpiece must be stationary and clamped or
u
held against both the fence and the table. Do not feed
the workpiece into the blade or cut "freehand" in any
way. Unrestrained or moving workpieces could be thrown
at high speeds, causing injury.
Push the saw through the workpiece. Do not pull the
u
saw through the workpiece. To make a cut, raise the
saw head and pull it out over the workpiece without
cutting, start the motor, press the saw head down and
push the saw through the workpiece. Cutting on the
pull stroke is likely to cause the saw blade to climb on top
of the workpiece and violently throw the blade assembly
towards the operator.
Never cross your hand over the intended line of cut-
u
ting either in front or behind the saw blade. Supporting
the workpiece "cross handed" i.e. holding the workpiece
to the right of the saw blade with your left hand or vice
versa is very dangerous.
Do not reach behind the fence with either hand closer
u
than 100 mm from either side of the saw blade, to re-
move wood scraps, or for any other reason while the
blade is spinning. The proximity of the spinning saw
blade to your hand may not be obvious and you may be
seriously injured.
Inspect your workpiece before cutting. If the work-
u
piece is bowed or warped, clamp it with the outside
bowed face toward the fence. Always make certain
that there is no gap between the workpiece, fence and
table along the line of the cut. Bent or warped work-
pieces can twist or shift and may cause binding on the
spinning saw blade while cutting. There should be no nails
or foreign objects in the workpiece.
Do not use the saw until the table is clear of all tools,
u
wood scraps, etc., except for the workpiece. Small
debris or loose pieces of wood or other objects that con-
tact the revolving blade can be thrown with high speed.
Cut only one workpiece at a time. Stacked multiple
u
workpieces cannot be adequately clamped or braced and
may bind on the blade or shift during cutting.
Ensure the mitre saw is mounted or placed on a level,
u
firm work surface before use. A level and firm work sur-
face reduces the risk of the mitre saw becoming unstable.
Plan your work. Every time you change the bevel or
u
mitre angle setting, make sure the adjustable fence is
set correctly to support the workpiece and will not in-
terfere with the blade or the guarding system. Without
English | 17
1 609 92A 6TT | (19.07.2021)