Connecting To Various Devices; Signals That Can Be Input To The Projector - JVC D-ILA DLA-QX1G Manuel D'instructions

Connecting to Various Devices

Signals that Can Be Input to the Projector

The following signals can be input to the projector through the corresponding VICs (Video Input Cards).
• Before connection, be sure to turn off the projector and devices.
• Read the manual which comes with each device thoroughly.
I Analog RGB signals
The signals with the following resolutions can be input to the input terminal of the RGB Analog VIC.
Screen resolution
(standard name)
DTV (480p 31.5kHz)
DTV (720p 60Hz)
DTV (1080p 60Hz)
VGA (640 X 480 60Hz)
VGA (640 X 480 75Hz)
VGA (640 X 480 85Hz)
VGA (640 X 480 Macintosh 13")
SVGA (800 X 600 85Hz)
SVGA (832 X 624 Macintosh 16")
XGA (1024 X 768 60Hz)
XGA (1024 X 768 70Hz)
XGA (1024 X 768 75Hz)
XGA (1024 X 768 85Hz)
XGA (1024 X 768 Macintosh 19")
XGA (1024 X 768 Macintosh 21")
SXGA (1280 X 1024 60Hz)
SXGA (1280 X 1024 67Hz)
SXGA (1280 X 1024 75Hz)
SXGA (1280 X 1024 76Hz)
SXGA (1280 X 1024 85Hz)
UXGA (1600 X 1200 60Hz)
UXGA (1600 X 1200 65Hz)
UXGA (1600 X 1200 70Hz)
UXGA (1600 X 1200 75Hz)
UXGA (1600 X 1200 85Hz)
QXGA (2048 X 1536 60Hz)
QXGA (2048 X 1536 60Hz)
• The RGB signals whose dot (pixel) clock is lower than 25 MHz or over 280 MHz are not available.
• The SVGA signals whose dot (pixel) clock is lower than 50 MHz are not available.
• When you want to input NTSC signal, make the signal twice as dense by a line doubler.
• The resolution and the scanning frequencies are within the range specified in the table on this page.
Be sure that the resolution and the scanning frequencies of the video signal are within the range. A video signal out of the
range cannot be used. (Even signals out of the range could be projected. However, it may not be sharp enough. On the
other hand, even some of the signals within the range may require adjustment depending on the video board used.)
When a signal other than listed in the table on this page is input, the image could be partially erased or an unneeded fold-
over image could appear.
Even signals within the frequency range may not be displayed normally depending on the type of the signal.
Composite sync (C ) and G on Sync signals cannot be handled depending on the devices connected.
S
I Analog HD signals
The HDTV interlaced signals can be input to the input terminal of the Analog HD VIC. NTSC is not available.
I Digital HD signals
The digital HD signals can be input to the input terminal of the HD-SDI VIC as the SDI format (and can be output through).
Horizontal
frequency frequency
31.5Hz
45.0kHz
67.5kHz
31.5kHz
37.5kHz
43.3kHz
35.0kHz
53.7kHz
49.8kHz
48.4kHz
56.5kHz
60.0kHz
68.7kHz
60.2kHz
68.7kHz
63.9kHz
70.8kHz
79.9kHz
81.2kHz
91.1kHz
75.0kHz
81.2kHz
87.5kHz
93.8kHz
106.3kHz
95.3kHz
95.7kHz
Vertical Effective number of
scanning line
59.9Hz
60.0Hz
60.0Hz 1080
59.9Hz
75.0Hz
85.0Hz
66.7Hz
85.0Hz
74.6Hz
60.0Hz
70.1Hz
75.0Hz
85.0Hz
74.9Hz
75.1Hz
60.0Hz 1024
67.0Hz 1024
75.0Hz 1024
76.2Hz 1024
85.0Hz 1024
60.0Hz 1200
65.0Hz 1200
70.0Hz 1200
75.0Hz 1200
85.0Hz 1200
59.9Hz 1536
60.0Hz 1536
483
720
480
480
480
480
600
624
768
768
768
768
768
870
25