Connecting To Various Devices; Signals That Can Be Input To The Projector - JVC DLA-M5000LE Manuel D'instructions

Connecting to Various Devices

* Before connection, be sure to turn off the projector and connected devices.
* Read the manual which comes with each device thoroughly.

Signals that Can Be Input to the Projector

The following signals can be input to the projector:
I Video signals
(1) Response to color systems
Color system
Input terminal
3
VIDEO*
3
Y/C*
Y, P /B-Y, P /R-Y
B R
G, B, R, H/C , V
S
*1: Responds if Y/C output is available.
*2: Signifies that component signals ("Y, P
(synchronization and video period) of each color system. The color systems are used for convenience only.
*3: To use these terminals, a video board (separately sold) is required.
(2) Response to double density (*1), high-vision signals
Input terminal
Y, P /B-Y, P /R-Y
B R
G, B, R, H/C , V
S
*4: Signals whose density of scanning lines/field is twice as high.
*5: Responds to signals whose horizontal scanning frequency is 31.5 kHz. NTSC can be made twice as dense by a line
doubler (separately available: recommended article). Also, possible to respond to fully-specified, decoded 525P
progressive signals.
Note
• DTV-format signals (480i, 480p, 720p, 1080i) can be input into this unit (Y, P
For details about DTV-format signals (480i, 480p, 720p, 1080i) compatible with this unit, refer to page 65.
I Computer signals
• Signals with the following resolutions can be input to the input terminal of RGB IN-1 (PC) or RGB IN-2 (G, B, R, H/C
(The following signals are preset.)
Screen resolution (standard name)
640 × 400 (PC-9801)
640 × 350 (VGA1)
640 × 480 (VGA3)
640 × 480 (Macintosh 13")
640 × 480 (VGA VESA)
800 × 600 (SVGA1)
800 × 600 (SVGA2)
832 × 624 (Macintosh 16")
1024 × 768 (XGA1)
1024 × 768 (XGA2)
1024 × 768 (Macintosh 19")
1152 × 870 (Macintosh 21")
1280 × 1024 (SXGA1)
1280 × 1024 (SXGA2)
1360 × 1024 (SXGA3: Mac Board)
Notes
• Interlace signals are not handled.
• Some signals other than listed above can be displayed. But they require adjustment. Even some of the signals listed above
may require adjustment depending on the video board used.
• When a signal other than listed above is input, the screen could be partially erased or an unneeded fold-over screen could
appear.
• Even signals in the frequency range that can be input may not be displayed normally depending on the type of the signal.
• Composite sync.(C ) and G on sync. signals can not handled depending on the devices connected.
S
18
NTSC 480i NTSC 4.43
‡
‡
‡
1
*
‡
2
*
, P " / "Y, B-Y, R-Y" / "G, B, R, H/C
B R
2 2 2 2
High-vision signal
NTSC*
‡
‡
Horizontal frequency
24.8kHz
31.5kHz
31.5kHz
35.0kHz
37.5kHz
37.9kHz
48.1kHz
49.7kHz
48.4kHz
56.5kHz
60.2kHz
68.7kHz
64.0kHz
70.8kHz
80.0kHz
PAL
‡ ‡
‡ ‡
1
*
‡ ‡
2
* *
‡ ‡
2
* *
, V") conform to the signal timing
S
‡
‡
/B-Y, P /R-Y input terminals).
B R
Vertical frequency
56.4Hz
70.1Hz
59.9Hz
66.7Hz
75.0Hz
60.3Hz
72.2Hz
74.6Hz
60.0Hz
70.1Hz
74.9Hz
75.0Hz
60.0Hz
67.0Hz
75.1Hz
SECAM
‡
-----
‡
2 2
*
‡
2
2
*
Scanning method
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
Non-interlace
, V).
S