Publicité
Les langues disponibles
Les langues disponibles
8.2) PROGRAMMING OPERATIONS ON THE APPLIANCE
3635 A
INSERT DATE
13 / 02 / 09
(DD / MM / YY)
Insert a different code from
the previous and from 0000.
It allows to access
the programming
Proceed with the programming accessing the various menus through ↵ and/or recalling the submenus with ↑↓
↑
TELEPHONE BOOK
↵
↓
CONFIRM
↑
TOOLS
↵
↓
CONFIRM
DIGITAL
↑
PROTOCOLS
↵
CONFIRM
8.3) Particular aspects of the various menus:
TELEPHONE BOOK
put ∗ in front of the programmed telephone numbers if the line is disturbed : the calls will leave without control of
Control phone line:
the line tone and the messages will be repeated 4 times.
use ↓ in order to allow (Y) or not the access to LOAD CONTROLS (6.2) of the appliance without typing the user's
Direct access Y/N:
code (recognising of the calling number).
Technical SMS coupling: SMS 1: dialler low battery
SMS 2: control unit/detectors low battery
SMS 3: lacking 12V
SMS 4: lacking of range GSM for more than 15min.
SMS 5: no positive outcome call on phone line
SMS 6: periodic call (live existence)
SMS 7: expiration SMS
SMS 8: restore 12V
in this position, recalled through the keys ↑↓ it is necessary to program the number provided by the provider for the
Position 64 :
request of residual credit, in order to allow the user of obtaining the information automatically (see 6.7)
speak with high voice near the microphone, spelling the words well. It needs to prepare before the written of the
MESSAGES recording:
several messages, that they must be adequate to the specific function.
INSTRUMENTS
Written/vocal labels:
Radio controls (5590):
Control units:
Remote controls (two ways): set Vocalphone then press the yellow key for 10 sec, and verify it: by pressing the key the combined messages
Detectors:
Caution:
SETTINGS enable functions: some functions must be activated using ↓ to commute N=no in Y=yes
Erasing:
DIGITAL PROTOCOLS:
SILENTRON - Made I n Italy
The appliance's firmware number
appears. Press ↵ , choose
the language using ↑↓
And proceed . . .
USER CODE
↵
_ _ _ _
↵
Memorization, recall and
cancellation of telephone
numbers and relative names
Wire control's programming
and/or via radio; writing and
registration of the labels
Setting of the protocol for the
alarm transmission to the
surveillance.
↓
(ask support to Silentron)
they are useful to the user in order to know the reason of the alarm in the most exact way when the appliance
calls, for which they must be provided as clear as possible.
in order to program such controls different operations are necessary according to the used TX:
set Vocalphone then arm/disarm control panel
will start, and will stop only by entering the user's/installers code on the dialler.
set Vocalphone, insert the battery in the detector and to verify it: any alarm starts the messages
always confirm with ↵ to memorize the set radio code.
the confirm eliminates all programmations
please refer to the appropriate manual for this programming or directly to the Silentron technical support (0039 -
0117732506 - silentron@silentron.it)
MANUFACTURER'S CODE
↵
0 0 0 0
To insert a code of 4-8 figures
different from 0000: this will be
useful for the user's interventions
Now the appliance is ready for programming
CONFIRM
↵
MESSAGES
SETTINGS
↵
CONFIRM
mod. 5150 - 5152 - 5590
mod. 5590
mod. 5150 - 5152
mod. 5150 - 5152 - 5590
mod. 5150 - 5590
mod. 5150 - 5152- 5590
mod. 5150 - 5152 - 5590 SMS
consequent to message 3
COPYRIGHT SILENTRON DFV.PHONEnewXA090616GM
INSERT TIME
↵
10 . 15
INSTALLER'S CODE
↵
_ _ _ _
↑
Registration of vocal messages
↓
and SMS writing
↑
Settings of particular functions
↓
and/or controls of the appliance
↵
10
Publicité
