HIKOKI CR 12DA Mode D'emploi page 7

h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specifi ed by the
manufacturer.
A charger that is suitable for one type of battery pack
may create a risk of fi re when used with another
battery pack.
b) Use power tools
designated battery packs.
Use of any other battery packs may create a risk of
injury and fi re.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another.
Shorting the battery terminals together may cause
burns or a fi re.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, fl ush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or
burns.
e) Do not use a battery pack or tool that is damaged
or modifi ed.
Damaged or modifi ed
unpredictable behaviour resulting in fi re, explosion
or risk of injury.
f) Do not expose a battery pack or tool to fi re or
excessive temperature.
Exposure to fi re or temperature above 130°C may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specifi ed in the instructions.
Charging improperly or at temperatures outside
the specifi ed range may damage the battery and
increase the risk of fi re.
6) Service
a) Have your power tool serviced by a qualifi ed
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed
by the manufacturer or authorized service providers.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
CORDLESS RECIPROCATING SAW
SAFETY WARNINGS
1. Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
2. Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the workpiece by hand or against your body
leaves it unstable and may lead to loss of control.
00Book̲CR12DA.indb 7 00Book̲CR12DA.indb 7
ADDITIONAL SAFETY WARNINGS
1. Preparing and checking the work environment. Make
2. Do not allow foreign matter to enter the hole for
3. Never disassemble the rechargeable battery and
4. Never
only with specifi cally
5. Do not dispose of the battery in fi re. If the battery is burnt,
6. Bring the battery to the shop from which it was purchased
7. Do not insert object into the air ventilation slots of the
8. When using this unit continuously, the unit may overheat,
9. If the machine is used continuously at low speed, an
batteries may exhibit
10. Always hold the body handle and housing of the
11. Mounting and dismounting the blade
○ Pull the back of the saw blade two or three times by hand
○ When pulling the saw blade, be absolutely sure to pull it
○ Never touch the saw blade immediately after use. The
○ If the broken saw blade is hidden inside the small slit,
○ After use, blow away sawdust, earth, sand, moisture,
○ Do not use any saw blade with a worn-out blade hole.
12. Make sure that the battery is installed fi rmly. If it is at all
13. Do not fi x and secure the switch lock. Besides, keep
14. Be careful not to let sawdust, earth, moisture, etc., enter
15. During use, press the base fi rmly against the workpiece.
16. Select a saw blade of the most appropriate length.
7
sure that the work site meets all the conditions laid forth
in the precautions.
connecting the rechargeable battery.
charger.
short-circuit the
Shortcircuiting the battery will cause a great electric
current and overheat. It results in burn or damage to the
battery.
it may explode.
as soon as the post-charging battery life becomes too
short for practical use. Do not dispose of the exhausted
battery.
charger. Inserting metal objects or infl ammables into the
charger air ventilation slots will result in electrical shock
hazard or damaged charger.
leading to damage in the motor and switch. Therefore,
whenever the housing becomes hot, give the saw a
break for a while.
extra load is applied to the motor which can result in
motor seizure. Always operate the power tool so that
the blade is not caught by the material during operation.
Always adjust the blade speed to enable smooth cutting.
power tool fi rmly as shown in Fig. 13. Otherwise the
counterforce produced may result in inaccurate and
even dangerous operation.
and check that the blade is securely mounted. When
pulling the blade, you will know it is properly mounted if it
clicks and the blade holder moves slightly. (Fig. 6-c)
from the back. Pulling other parts of the blade will result
in an injury.
metal is hot and can easily burn your skin.
hook the broken blade using a tip of another saw blade
and take it out. (Fig. 8-b)
etc., with air or brush them away with a brush, etc., to
ensure that the blade mount can function smoothly.
Otherwise, the saw blade can come off , resulting in
personal injury.
loose it could come off and cause an accident.
your fi nger off the switch trigger when the tool is being
carried around. Otherwise, the main body switch can
be inadvertently turned ON, resulting in unexpected
accidents.
the inside of the machine through the plunger section
during operation. If sawdust and the like accumulate in
the plunger section, always clean it before use.
Ideally, the length protruding from the base of the saw
blade after subtracting the stroke quantity should be
larger than the material.
English
rechargeable battery.
2021/02/02 17:14:17 2021/02/02 17:14:17